----- Original Message ----- From: "Tim Farrington" <timf@xxxxxxxxxxxx> To: "David" <dvb-t@xxxxxxxxxxxx> Cc: <linux-dvb@xxxxxxxxxxx> Sent: Thursday, August 07, 2008 2:34 PM Subject: Re: [PATCH] Add initial support for DViCO FusionHDTV DVB-T Dual Express > David wrote: >> Hi Tim >> >> Thanks for information. >> >> I obtained the driver, extracted the firmware to lib/firmware and tried >> to scan. >> I cannot get a lock on anything. >> >> dmesg shows it is loading the firmware but nothing more: >> >> [ 192.596627] xc2028 1-0061: Loading 3 firmware images from >> xc3028-v27.fw, type: DViCO DualDig4/Nano2 (Australia), ver 2.7 >> [ 192.796658] xc2028 1-0061: Loading firmware for type=BASE F8MHZ (3), >> id 0000000000000000. >> [ 193.965865] xc2028 1-0061: Loading firmware for type=D2620 DTV7 (88), >> id 0000000000000000. >> [ 265.268818] xc2028 2-0061: Loading 3 firmware images from >> xc3028-v27.fw, type: DViCO DualDig4/Nano2 (Australia), ver 2.7 >> [ 265.468693] xc2028 2-0061: Loading firmware for type=BASE F8MHZ (3), >> id 0000000000000000. >> [ 266.633170] xc2028 2-0061: Loading firmware for type=D2620 DTV7 (88), >> id 0000000000000000. >> >> >> Regards >> David >> >> >> >> ----- Original Message ----- From: "Tim Farrington" <timf@xxxxxxxxxxxx> >> To: "David Porter" <dvb-t@xxxxxxxxxxxx> >> Cc: <linux-dvb@xxxxxxxxxxx> >> Sent: Wednesday, August 06, 2008 6:51 PM >> Subject: Re: [PATCH] Add initial support for DViCO FusionHDTV >> DVB-T Dual Express >> >> >>> David Porter wrote: >>>> Hi >>>> >>>> I have one of these, saw Stevens post and thought i would give it a go. >>>> >>>> I built from : http://linuxtv.org/hg/~stoth/v4l-dvb >>>> All seemed to go well with no errors. >>>> >>>> dmesg reads: >>>> >>>> [ 31.964424] CORE cx23885[0]: subsystem: 18ac:db78, board: DViCO >>>> FusionHDTV DVB-T Dual Express [card=11,autodetected] >>>> [ 32.104767] cx23885[0]: i2c bus 0 registered >>>> [ 32.104781] cx23885[0]: i2c bus 1 registered >>>> [ 32.104794] cx23885[0]: i2c bus 2 registered >>>> [ 32.164385] input: i2c IR (FusionHDTV) as >>>> /devices/virtual/input/input8 >>>> [ 32.422764] ir-kbd-i2c: i2c IR (FusionHDTV) detected at >>>> i2c-1/1-006b/ir0 [cx23885[0]] >>>> [ 32.423135] cx23885[0]: cx23885 based dvb card >>>> [ 32.492021] xc2028 1-0061: creating new instance >>>> [ 32.492027] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner >>>> [ 32.492036] DVB: registering new adapter (cx23885[0]) >>>> [ 32.492040] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... >>>> [ 32.492386] cx23885[0]: cx23885 based dvb card >>>> [ 32.492924] xc2028 2-0061: creating new instance >>>> [ 32.492926] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner >>>> [ 32.492928] DVB: registering new adapter (cx23885[0]) >>>> [ 32.492930] DVB: registering frontend 1 (Zarlink ZL10353 DVB-T)... >>>> [ 32.493228] cx23885_dev_checkrevision() Hardware revision = 0xb0 >>>> [ 32.493236] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, >>>> latency: 0, mmio: 0xfe800000 >>>> >>>> But scanning, returns : >>>> >>>> [ 1381.214624] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. >>>> [ 1382.220858] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. >>>> [ 1382.260825] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. >>>> [ 1383.267724] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. >>>> [ 1383.276680] xc2028 1-0061: Error: firmware xc3028-v27.fw not found. >>>> >>>> I checked /lib/firmware/ but xc3028-v27.fw is not in the directory ? >>>> >>>> Must have messed it up somewhere! Any help appreciated. >>>> >>>> Thanks >>>> David >>>> >>>> ----- Original Message ----- From: "Steven Toth" <stoth@xxxxxxxxxxx> >>>> To: "Luke Yelavich" <themuso@xxxxxxxxxxx> >>>> Cc: <linux-dvb@xxxxxxxxxxx> >>>> Sent: Wednesday, August 06, 2008 11:44 AM >>>> Subject: Re: [PATCH] Add initial support for DViCO >>>> FusionHDTV DVB-T Dual Express >>>> >>>> >>>> >>>>>>>> I've tested with the HVR1500Q (xc5000 based) and I'm happy with the >>>>>>>> results. Can you both try the DViCO board? >>>>>>>> >>>>>>> It tests fine and I like how simpler things have got. >>>>>>> >>>>>> I pulled the above linked tree, and compiled the modules. It seems at >>>>>> the moment for the dual express, that I have to pass the parameter >>>>>> card=11 to the driver, for it to correctly find the card and make use >>>>>> of all adapters. Without any module parameters, dmsg complains that >>>>>> the card couldn't be identified, yet two adapters are shown. I have >>>>>> two of these cards. >>>>>> >>>>>> Hope this helps some. >>>>>> >>>>> .. And they're both the same model? >>>>> >>>>> If so, insert one at a time and run the 'lspci -vn' command, save the >>>>> output for each card. >>>>> >>>>> Post the output here. >>>>> >>>>> Assuming you load the driver with card=11, does each card work >>>>> correctly >>>>> after that? >>>>> >>>>> - Steve >>>>> >>>>> _______________________________________________ >>>>> linux-dvb mailing list >>>>> linux-dvb@xxxxxxxxxxx >>>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>>>> >>>>> >>>> >>>> _______________________________________________ >>>> linux-dvb mailing list >>>> linux-dvb@xxxxxxxxxxx >>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>>> >>>> >>> >>> To obtain xc3028-v27.fw >>> >>> see ~/v4l-dvb/linux/Documentation/video4linux/extract_xc3028.pl >>> >>> Regards, >>> Timf >> > Try not to top post. > > Best to post the results of tzap here: > > In Ubuntu, Debian; > sudo apt-get install dvb-utils > (other distros use dvb-apps) > > Find the scan file appropriate for your area (au-*) in: > /usr/share/doc/dvb-utils/examples/scan/dvb-t > > sudo -s -H > mkdir /root/.tzap > scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-* > > /root/.tzap/channels.conf > > Post the output of scan to this list. > > Regards, > Timf Thanks, Tim Doesn't look too promising : a@a-desktop:~$ scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Brisbane scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Brisbane using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 226500000 1 3 9 3 1 1 0 initial transponder 177500000 1 2 9 3 1 2 0 initial transponder 191625000 1 3 9 3 1 1 0 initial transponder 219500000 1 3 9 3 1 1 0 initial transponder 585625000 1 2 9 3 1 2 0 >>> tune to: >>> 226500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 226500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE >>> (tuning failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE >>> (tuning failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 191625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 191625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE >>> (tuning failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 219500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 219500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE >>> (tuning failed) WARNING: >>> tuning failed!!! >>> tune to: >>> 585625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: >>> 585625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE >>> (tuning failed) WARNING: >>> tuning failed!!! ERROR: initial tuning failed dumping lists (0 services) Done. a@a-desktop:~$ Regards David _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
