ok - now I'm using (again) the xc-test branch with options card=5 and xc_2028 debug enabled. the output posted before (see: autodetecting card=10) was your patch - I deleted all modules and started new. [ 50.371020] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 50.371035] CORE cx23885[0]: subsystem: 18ac:db78, board: DViCO FusionHDTV DVB-T Dual Express [card=5,insmod option] [ 50.470993] cx23885[0]: i2c bus 0 registered [ 50.471008] cx23885[0]: i2c bus 1 registered [ 50.471027] cx23885[0]: i2c bus 2 registered ... [ 50.538957] input: i2c IR (FusionHDTV) as /class/input/input3 [ 50.538976] ir-kbd-i2c: i2c IR (FusionHDTV) detected at i2c-3/3-006b/ir0 [cx23885[0]] [ 50.540006] cx23885[0]: cx23885 based dvb card [ 50.596214] xc2028: Xcv2028/3028 init called! [ 50.596219] xc2028 3-0061: type set to XCeive xc2028/xc3028 tuner [ 50.596222] xc2028 3-0061: xc2028_set_config called [ 50.596228] DVB: registering new adapter (cx23885[0]) [ 50.596232] DVB: registering frontend 2 (Zarlink ZL10353 DVB-T)... [ 50.596472] cx23885[0]: cx23885 based dvb card [ 50.601980] xc2028: Xcv2028/3028 init called! [ 50.601983] xc2028 4-0061: type set to XCeive xc2028/xc3028 tuner [ 50.601985] xc2028 4-0061: xc2028_set_config called [ 50.601988] DVB: registering new adapter (cx23885[0]) [ 50.601990] DVB: registering frontend 3 (Zarlink ZL10353 DVB-T)... [ 50.602198] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfd600000 [ 50.602206] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 50.601721] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16 ... now VDR starts and then... ... [ 95.874136] xc2028 3-0061: xc2028_set_params called [ 95.874141] xc2028 3-0061: generic_set_freq called [ 95.874144] xc2028 3-0061: should set frequency 514000 kHz [ 95.874146] xc2028 3-0061: check_firmware called [ 95.874148] xc2028 3-0061: load_all_firmwares called [ 95.874150] xc2028 3-0061: Reading firmware xc3028-dvico-au-01.fw [ 95.875949] xc2028 4-0061: xc2028_set_params called [ 95.875957] xc2028 4-0061: generic_set_freq called [ 95.875960] xc2028 4-0061: should set frequency 538000 kHz [ 95.875979] xc2028 4-0061: check_firmware called [ 95.875990] xc2028 4-0061: load_all_firmwares called [ 95.876006] xc2028 4-0061: Reading firmware xc3028-dvico-au-01.fw [ 95.885803] xc2028 3-0061: Loading 3 firmware images from xc3028-dvico-au-01.fw, type: DViCO DualDig4/Nano2 (Australia), ver 2.7 [ 95.885810] xc2028 3-0061: Reading firmware type DTV7 ZARLINK456 SCODE (22000080), id 0, size=224. [ 95.885819] xc2028 3-0061: Reading firmware type BASE F8MHZ (3), id 0, size=8718. [ 95.885826] xc2028 3-0061: Reading firmware type D2620 DTV7 (88), id 0, size=149. [ 95.885835] xc2028 3-0061: Firmware files loaded. [ 95.885837] xc2028 3-0061: checking firmware, user requested type=F8MHZ D2620 DTV8 (20a), id 0000000000000000, scode_tbl ZARLINK456 (2000000), scode_nr 0 [ 95.888064] xc2028 4-0061: Loading 3 firmware images from xc3028-dvico-au-01.fw, type: DViCO DualDig4/Nano2 (Australia), ver 2.7 [ 95.888069] xc2028 4-0061: Reading firmware type DTV7 ZARLINK456 SCODE (22000080), id 0, size=224. [ 95.888080] xc2028 4-0061: Reading firmware type BASE F8MHZ (3), id 0, size=8718. [ 95.888088] xc2028 4-0061: Reading firmware type D2620 DTV7 (88), id 0, size=149. [ 95.888101] xc2028 4-0061: Firmware files loaded. [ 95.888103] xc2028 4-0061: checking firmware, user requested type=F8MHZ D2620 DTV8 (20a), id 0000000000000000, scode_tbl ZARLINK456 (2000000), scode_nr 0 [ 95.888226] xc2028 3-0061: load_firmware called [ 95.888229] xc2028 3-0061: seek_firmware called, want type=BASE F8MHZ D2620 DTV8 (20b), id 0000000000000000. [ 95.888233] xc2028 3-0061: Found firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 95.888236] xc2028 3-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 95.890514] xc2028 4-0061: load_firmware called [ 95.890517] xc2028 4-0061: seek_firmware called, want type=BASE F8MHZ D2620 DTV8 (20b), id 0000000000000000. [ 95.890524] xc2028 4-0061: Found firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 95.890561] xc2028 4-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 96.343671] xc2028 3-0061: Load init1 firmware, if exists [ 96.343676] xc2028 3-0061: load_firmware called [ 96.343678] xc2028 3-0061: seek_firmware called, want type=BASE INIT1 F8MHZ D2620 DTV8 (420b), id 0000000000000000. [ 96.343684] xc2028 3-0061: Can't find firmware for type=BASE INIT1 F8MHZ (4003), id 0000000000000000. [ 96.343688] xc2028 3-0061: load_firmware called [ 96.343690] xc2028 3-0061: seek_firmware called, want type=BASE INIT1 D2620 DTV8 (4209), id 0000000000000000. [ 96.343693] xc2028 3-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000. [ 96.343697] xc2028 3-0061: load_firmware called [ 96.343699] xc2028 3-0061: seek_firmware called, want type=F8MHZ D2620 DTV8 (20a), id 0000000000000000. [ 96.343702] xc2028 3-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 96.343706] xc2028 3-0061: load_firmware called [ 96.343708] xc2028 3-0061: seek_firmware called, want type=D2620 DTV8 (208), id 0000000000000000. [ 96.343711] xc2028 3-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 96.367858] xc2028 3-0061: Retrying firmware load [ 96.367862] xc2028 3-0061: checking firmware, user requested type=F8MHZ D2620 DTV8 (20a), id 0000000000000000, scode_tbl ZARLINK456 (2000000), scode_nr 0 [ 96.370251] xc2028 3-0061: load_firmware called [ 96.370253] xc2028 3-0061: seek_firmware called, want type=BASE F8MHZ D2620 DTV8 (20b), id 0000000000000000. [ 96.370258] xc2028 3-0061: Found firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 96.370261] xc2028 3-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 96.384954] xc2028 4-0061: Load init1 firmware, if exists [ 96.384959] xc2028 4-0061: load_firmware called [ 96.384961] xc2028 4-0061: seek_firmware called, want type=BASE INIT1 F8MHZ D2620 DTV8 (420b), id 0000000000000000. [ 96.384967] xc2028 4-0061: Can't find firmware for type=BASE INIT1 F8MHZ (4003), id 0000000000000000. [ 96.384970] xc2028 4-0061: load_firmware called [ 96.384972] xc2028 4-0061: seek_firmware called, want type=BASE INIT1 D2620 DTV8 (4209), id 0000000000000000. [ 96.384976] xc2028 4-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000. [ 96.385014] xc2028 4-0061: load_firmware called [ 96.385016] xc2028 4-0061: seek_firmware called, want type=F8MHZ D2620 DTV8 (20a), id 0000000000000000. [ 96.385019] xc2028 4-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 96.385023] xc2028 4-0061: load_firmware called [ 96.385025] xc2028 4-0061: seek_firmware called, want type=D2620 DTV8 (208), id 0000000000000000. [ 96.385028] xc2028 4-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 96.409295] xc2028 4-0061: Retrying firmware load [ 96.409299] xc2028 4-0061: checking firmware, user requested type=F8MHZ D2620 DTV8 (20a), id 0000000000000000, scode_tbl ZARLINK456 (2000000), scode_nr 0 [ 96.411713] xc2028 4-0061: load_firmware called [ 96.411715] xc2028 4-0061: seek_firmware called, want type=BASE F8MHZ D2620 DTV8 (20b), id 0000000000000000. [ 96.411719] xc2028 4-0061: Found firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 96.411723] xc2028 4-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. ... [ 372.810622] xc2028 4-0061: should set frequency 698000 kHz [ 372.810624] xc2028 4-0061: check_firmware called [ 372.810626] xc2028 4-0061: checking firmware, user requested type=F8MHZ D2620 DTV8 (20a), id 0000000000000000, scode_tbl ZARLINK456 (2000000), scode_nr 0 [ 372.815396] xc2028 4-0061: load_firmware called [ 372.815399] xc2028 4-0061: seek_firmware called, want type=BASE F8MHZ D2620 DTV8 (20b), id 0000000000000000. [ 372.815403] xc2028 4-0061: Found firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 372.815406] xc2028 4-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 373.715341] xc2028 3-0061: Load init1 firmware, if exists [ 373.715355] xc2028 3-0061: load_firmware called [ 373.715358] xc2028 3-0061: seek_firmware called, want type=BASE INIT1 F8MHZ D2620 DTV8 (420b), id 0000000000000000. [ 373.715364] xc2028 3-0061: Can't find firmware for type=BASE INIT1 F8MHZ (4003), id 0000000000000000. [ 373.715368] xc2028 3-0061: load_firmware called [ 373.715370] xc2028 3-0061: seek_firmware called, want type=BASE INIT1 D2620 DTV8 (4209), id 0000000000000000. [ 373.715374] xc2028 3-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000. [ 373.715378] xc2028 3-0061: load_firmware called [ 373.715380] xc2028 3-0061: seek_firmware called, want type=F8MHZ D2620 DTV8 (20a), id 0000000000000000. [ 373.715383] xc2028 3-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 373.715387] xc2028 3-0061: load_firmware called [ 373.715389] xc2028 3-0061: seek_firmware called, want type=D2620 DTV8 (208), id 0000000000000000. [ 373.715392] xc2028 3-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 373.732296] xc2028 4-0061: Load init1 firmware, if exists [ 373.732301] xc2028 4-0061: load_firmware called [ 373.732303] xc2028 4-0061: seek_firmware called, want type=BASE INIT1 F8MHZ D2620 DTV8 (420b), id 0000000000000000. [ 373.732309] xc2028 4-0061: Can't find firmware for type=BASE INIT1 F8MHZ (4003), id 0000000000000000. [ 373.732313] xc2028 4-0061: load_firmware called [ 373.732315] xc2028 4-0061: seek_firmware called, want type=BASE INIT1 D2620 DTV8 (4209), id 0000000000000000. [ 373.732319] xc2028 4-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000. [ 373.732323] xc2028 4-0061: load_firmware called [ 373.732325] xc2028 4-0061: seek_firmware called, want type=F8MHZ D2620 DTV8 (20a), id 0000000000000000. [ 373.732328] xc2028 4-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 373.732332] xc2028 4-0061: load_firmware called [ 373.732334] xc2028 4-0061: seek_firmware called, want type=D2620 DTV8 (208), id 0000000000000000. [ 373.732337] xc2028 4-0061: Can't find firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 373.735760] xc2028 3-0061: xc2028_set_params called [ 373.735765] xc2028 3-0061: generic_set_freq called ... and so on. several firmware (partial) can not be found? and does "Loading 3 firmware images from xc3028-dvico-au-01.fw, type: DViCO DualDig4/Nano2 (Australia), ver 2.7" mean wrong card detected? jochen Am Dienstag 20 Mai 2008 23:45:48 schrieb stev391@xxxxxxxxx: > Jochen, > > Which sources is this dmesg output from (my patch or Chris Pascoe's > xc-test branch)? Mine are definately dead in the water at the moment as > the existing code relies on the moons alligning to work. I'm still > working on this... > > If it is from Chris Pascoe's branch it should work, if not for the module > "tuner_xc2028" when loading pass the option debug=1 (This will generate > alot more lines in dmesg) and repeat whatever you did to break it. Send > this on and I will attempt to work out where it is going wrong. > > Regards, > Stephen > > ----- Original Message ----- > From: "jochen s" > To: linux-dvb@xxxxxxxxxxx > Subject: Re: DViCO Fusion HDTV DVB-T Dual Express [PATCH] > Date: Tue, 20 May 2008 18:10:26 +0200 > > > > May 20 17:48:11 kernel: [ 48.744161] ACPI: PCI Interrupt 0000:02:00.0 > [A] -> GSI 16 (level, low) -> IRQ 16 > May 20 17:48:11 kernel: [ 48.744179] CORE cx23885[0]: subsystem: > 18ac:db78, board: DViCO FusionHDTV DVB-T Dual Express > [card=10,autodetected] > May 20 17:48:11 kernel: [ 48.844132] cx23885[0]: i2c bus 0 registered > May 20 17:48:11 kernel: [ 48.844154] cx23885[0]: i2c bus 1 registered > May 20 17:48:11 kernel: [ 48.844168] cx23885[0]: i2c bus 2 registered > May 20 17:48:11 kernel: [ 48.908665] input: i2c IR (FusionHDTV) > as /class/input/input3 > May 20 17:48:11 kernel: [ 48.908687] ir-kbd-i2c: i2c IR (FusionHDTV) > detected at i2c-2/2-006b/ir0 [cx23885[0]] > May 20 17:48:11 kernel: [ 48.909711] cx23885[0]: cx23885 based dvb > card > May 20 17:48:11 kernel: [ 48.970326] xc2028 2-0061: type set to > XCeive > xc2028/xc3028 tuner > May 20 17:48:11 kernel: [ 48.970336] DVB: registering new adapter > (cx23885 > [0]) > May 20 17:48:11 kernel: [ 48.970340] DVB: registering frontend 1 > (Zarlink > ZL10353 DVB-T)... > May 20 17:48:11 kernel: [ 48.970625] cx23885[0]: cx23885 based dvb > card > May 20 17:48:11 kernel: [ 48.976144] xc2028 3-0061: type set to > XCeive > xc2028/xc3028 tuner > May 20 17:48:11 kernel: [ 48.976147] DVB: registering new adapter > (cx23885 > [0]) > May 20 17:48:11 kernel: [ 48.976151] DVB: registering frontend 2 > (Zarlink > ZL10353 DVB-T)... > May 20 17:48:11 kernel: [ 48.976368] cx23885_dev_checkrevision() > Hardware > revision = 0xb0 > May 20 17:48:11 kernel: [ 48.976376] cx23885[0]/0: found at > 0000:02:00.0, > rev: 2, irq: 16, latency: 0, mmio: 0xfd600000 > May 20 17:48:11 kernel: [ 48.976383] PCI: Setting latency timer of > device > 0000:02:00.0 to 64 > > ok - so far... > > but then: > > May 20 17:48:50 vdr: [7428] frontend 1 timed out while tuning to > channel 2, > tp 514 > May 20 17:48:50 kernel: [ 80.313642] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:48:51 kernel: [ 81.247786] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:48:53 kernel: [ 83.150433] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:48:53 kernel: [ 83.720342] eth0: no IPv6 routers present > May 20 17:48:54 kernel: [ 84.117987] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:48:56 kernel: [ 86.047256] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:48:57 kernel: [ 86.979688] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > ... > May 20 17:48:59 kernel: [ 88.486428] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:49:00 kernel: [ 89.498026] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:49:02 kernel: [ 91.416250] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:49:03 kernel: [ 92.346871] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > ... > May 20 17:49:23 kernel: [ 109.368185] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:49:24 kernel: [ 109.934506] xc2028 3-0061: Loading 3 > firmware > images from xc3028-dvico-au-01.fw, type: DViCO DualDig4/Nano2 > (Australia), > ver 2.7 > May 20 17:49:24 kernel: [ 109.938812] xc2028 3-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:49:24 kernel: [ 110.034395] xc2028 2-0061: i2c output > error: rc > = -5 (should be 4) > May 20 17:49:24 kernel: [ 110.034399] xc2028 2-0061: -5 returned from > send > May 20 17:49:24 kernel: [ 110.034434] xc2028 2-0061: Error -22 while > loading base firmware > May 20 17:49:24 kernel: [ 110.081951] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 17:49:24 kernel: [ 110.088001] xc2028 2-0061: i2c output > error: rc > = -5 (should be 64) > May 20 17:49:24 kernel: [ 110.088003] xc2028 2-0061: -5 returned from > send > May 20 17:49:24 kernel: [ 110.088050] xc2028 2-0061: Error -22 while > loading base firmware > May 20 17:49:24 kernel: [ 110.089843] zl10353: write to reg 62 failed > (err > = -5)! > May 20 17:49:24 kernel: [ 110.091667] zl10353: write to reg 5f failed > (err > = -5)! > May 20 17:49:24 kernel: [ 110.093428] zl10353: write to reg 71 failed > (err > = -5)! > May 20 17:49:24 kernel: [ 110.095201] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 17:49:24 kernel: [ 110.105956] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 17:49:24 kernel: [ 110.116251] zl10353_read_register: readreg > error > (reg=6, ret==-5) > ... > > May 20 18:01:00 kernel: [ 791.122235] xc2028 3-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 18:01:01 kernel: [ 791.998348] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 18:01:02 kernel: [ 793.049839] xc2028 2-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 18:01:02 kernel: [ 793.144856] xc2028 3-0061: Loading firmware > for > type=BASE F8MHZ (3), id 0000000000000000. > May 20 18:01:03 kernel: [ 794.054455] xc2028 2-0061: i2c output > error: rc > = -5 (should be 4) > May 20 18:01:03 kernel: [ 794.054460] xc2028 2-0061: -5 returned from > send > May 20 18:01:03 kernel: [ 794.054528] xc2028 2-0061: Error -22 while > loading base firmware > May 20 18:01:03 kernel: [ 794.056622] zl10353: write to reg 62 failed > (err > = -5)! > May 20 18:01:03 kernel: [ 794.058744] zl10353: write to reg 5f failed > (err > = -5)! > May 20 18:01:03 kernel: [ 794.060858] zl10353: write to reg 71 failed > (err > = -5)! > May 20 18:01:03 kernel: [ 794.063013] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 18:01:03 kernel: [ 794.075006] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 18:01:03 kernel: [ 794.087060] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 18:01:03 kernel: [ 794.098969] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 18:01:03 kernel: [ 794.111100] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 18:01:03 kernel: [ 794.122939] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 18:01:03 kernel: [ 794.135009] zl10353_read_register: readreg > error > (reg=6, ret==-5) > May 20 18:01:03 kernel: [ 794.148908] zl10353_read_register: readreg > error > (reg=6, ret==-5) > > any idea to help me? > > thanks in advance, jochen > > Am Donnerstag 15 Mai 2008 00:12:52 schrieb stev391@xxxxxxxxx: > > Thom, > > > > Disclaimer: This not guranteed to work and will break any webcams > > you > > > have running on ubuntu, this is reversable by reinstalling the > > "linux-*" > > > packages that you have already installed. > > > > I can't seem to find any information about that version of > > Mythbuntu, is > > > it supposed to be version 8.04? Anyway the following will work for > > previous versions as well. > > All commands to be run in a terminal. > > > > Step 1, Install the required packages to retrieve and compile the > > source > > > (you also need to install the linux-headers that match your kernel, > > which > > > is done by the following command as well) > > sudo apt-get install mercurial build-essential patch > > linux-headers-`uname > > > -r` > > > > Step 2, Retrieve the v4l-dvb sources > > hg clone http://linuxtv.org/hg/v4l-dvb > > > > Step 3, Apply patch (which was an attachment on the previous email) > > cd v4l-dvb > > patch -p1 < ../DViCO_FUSIONHDTV_DVB_T_DUAL_EXP_v2.patch > > > > Step 4, Compile which will take awhile... (maybe time to make a cup > > of > > > coffee) > > make all > > > > Step 5 Remove the old modules as this causes issues when loading > > the > > > modules later(this depends on version of ubuntu) > > 8.04: cd /lib/modules/`uname -r`/ubuntu/media > > cd /lib/modules/`uname -r`/kernel/drivers/media > > sudo rm -r common > > sudo rm -r dvb > > sudo rm -r radio > > sudo rm -r video > > > > Step 6: return to v4l-dvb directory and run: > > sudo make install > > > > Step 7: Update the initramfs: > > sudo dpkg-reconfigure linux-ubuntu-modules-`uname -r` > > > > Step 8: Reboot and see if it worked > > sudo shutdown -r now > > > > If this didn't work with my patch please send me the output of > > dmesg and > > > any relevant logs of the application that you used to identify the > > problem with (eg mythbackend log). Then try replacing step 2 & 3 > > with > > > (This uses the older branch by Chris Pascoe, whose code I'm trying > > to > > > update to bring into the main v4l-dvb): > > hg clone http://linuxtv.org/hg/~pascoe/xc-test/ > > cd xc-test > > > > If this still doesn't work and your dvb system is broken just > > reinstall > > > your linux-* packages. > > > > Regards, > > Stephen _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
