Jarryd Beck wrote: > I found the problem, the driver I had set .no_reconnect = 1 in > af9015_properties, the one in af9015_new didn't. So after I changed > that I tried again, it still didn't work. I enabled debugging and tried > to tune to a channel and this is what I got in dmesg. I know this no_reconnect problem. But haven't found proper correction yet. Looks like sometimes with some hw / sw configuration it reconnects USB-bus after firmware download and sometimes not. When there is no_reconnect set it is possible that driver loads twice (two adapters) and it causes race condition when two drivers are accessing same hw same time and it hangs (remote polling causes hangs very soon after plug). You can help and test if it is OK set no_reconnect=0 and remove #if 0 -killed code by changing it to #if 1 in line where is comment "firmware is running, reconnect device in the usb bus". This forces AF9015 chipset reconnect USB. > > usb 2-10: new high speed USB device using ehci_hcd and address 27 > usb 2-10: configuration #1 chosen from 1 choice > af9015_usb_probe: > af9015_identify_state: reply:01 > dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in cold state, > will try to load a firmware > dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw' > af9015_download_firmware: > dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in warm state. > dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. > DVB: registering new adapter (Afatech AF9015 DVB-T USB2.0 stick) > af9015_eeprom_dump: > 00: 31 c2 bb 0b 00 00 00 00 13 04 29 60 00 02 01 02 > 10: 00 80 00 fa fa 10 40 ef 01 30 31 30 31 30 32 30 > 20: 35 30 35 30 30 30 30 31 ff ff ff ff ff ff ff ff > 30: 00 00 3a 01 00 08 02 00 cc 10 00 00 9c ff ff ff > 40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff > 50: ff ff ff ff ff 26 00 00 04 03 09 04 10 03 4c 00 > 60: 65 00 61 00 64 00 74 00 65 00 6b 00 30 03 57 00 > 70: 69 00 6e 00 46 00 61 00 73 00 74 00 20 00 44 00 > 80: 54 00 56 00 20 00 44 00 6f 00 6e 00 67 00 6c 00 > 90: 65 00 20 00 47 00 6f 00 6c 00 64 00 20 03 30 00 > a0: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00 > b0: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff > c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > af9015_read_config: xtal:2 set adc_clock:28000 > af9015_read_config: tuner id1:156 > af9015_read_config: spectral inversion:0 > af9015_set_gpios: > af9013: firmware version:4.95.0 > DVB: registering frontend 0 (Afatech AF9013 DVB-T)... > af9015_tuner_attach: > af9015_tda18271_tuner_attach: > tda18271 5-00c0: creating new instance > TDA18271HD/C1 detected @ 5-00c0 > tda18271_init_regs: initializing registers for device @ 5-00c0 > input: IR-receiver inside an USB DVB receiver as /class/input/input39 > dvb-usb: schedule remote query interval to 200 msecs. > dvb-usb: Afatech AF9015 DVB-T USB2.0 stick successfully initialized > and connected. > af9015_init: > af9015_download_ir_table: > input: Leadtek WinFast DTV Dongle Gold as /class/input/input40 > input: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on > usb-0000:00:02.1-10 > tda18271_set_standby_mode: sm = 0, sm_lt = 0, sm_xt = 0 > tda18271_init_regs: initializing registers for device @ 5-00c0 > tda18271_tune: freq = 219500000, ifc = 3800000, bw = 7000000, std = 0x1d > tda18271_set_standby_mode: sm = 0, sm_lt = 0, sm_xt = 0 > tda18271_init_regs: initializing registers for device @ 5-00c0 > tda18271_set_standby_mode: sm = 1, sm_lt = 0, sm_xt = 0 There is no debug logs from af9013 demodulator module. You can enable logs by modprobe af9013 debug=1. Remember rmmod modules first from memory rmmod dvb_usb_af9015 af9013 mt2060 dvb_usb dvb_core af9013 debug should log rather much useful data when tuning to channel. Did you try change GPIO3 as mentioned earlier? regards Antti -- http://palosaari.fi/ _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
