Albert, your dmesg output looks quite good. In fact, the only line that irritates me is the line with xc2028 4-0061: Error on line 1063: -5 This line indicates an i2c-communication problem with the tuner. As it happens BEFORE the XC3028 firmware is loaded, it cannot have anything to do with the xc3028 firmware. Therefore, I suspect something either with the general setup of the Expresscard or a DiB firmware that does not 100% support your device. Have you tried a later firmware? For comparison, I list here what is output in kernel.log for my Cinergy HT USB XE: Feb 13 19:13:31: usb 1-5: new high speed USB device using ehci_hcd and address 6 Feb 13 19:13:31: usb 1-5: configuration #1 chosen from 1 choice Feb 13 19:13:31: dib0700: loaded with support for 7 different device-types Feb 13 19:13:31: dvb-usb: found a 'Terratec Cinergy HT USB XE' in cold state, will try to load a firmware Feb 13 19:13:31: dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw' Feb 13 19:13:32: dib0700: firmware started successfully. Feb 13 19:13:32: dvb-usb: found a 'Terratec Cinergy HT USB XE' in warm state. Feb 13 19:13:32: dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Feb 13 19:13:32: DVB: registering new adapter (Terratec Cinergy HT USB XE) Feb 13 19:13:33: DVB: registering frontend 1 (DiBcom 7000PC)... Feb 13 19:13:33: xc2028 7-0061: type set to XCeive xc2028/xc3028 tuner Feb 13 19:13:33: input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:02.1/usb1/1-5/input/input6 Feb 13 19:13:33: dvb-usb: schedule remote query interval to 150 msecs. Feb 13 19:13:33: dvb-usb: Terratec Cinergy HT USB XE successfully initialized and connected. Feb 13 19:13:33: usbcore: registered new interface driver dvb_usb_dib0700 Feb 13 19:14:43: xc2028 7-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 Feb 13 19:14:43: dib0700: stk7700ph_xc3028_callback: XC2028_TUNER_RESET 0 Feb 13 19:14:43: Feb 13 19:14:43: xc2028 7-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. Feb 13 19:14:43: dib0700: stk7700ph_xc3028_callback: XC2028_TUNER_RESET 0 Feb 13 19:14:43: Feb 13 19:14:50: xc2028 7-0061: Loading firmware for type=D2620 DTV8 (208), id 0000000000000000. Feb 13 19:14:50: xc2028 7-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 Feb 13 19:14:50: dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 Feb 13 19:14:50: with regards to the firmware modification that I mentioned, see the comment below. Regards, Hans-Frieder > Finally I got what you mean... you changed the extract_firmware.pl, but not > only the comment I guess... also the values below. I tested both and the I did not change the extract_firmware.pl file (in fact, it is not useable for the Mod7700.sys driver, but expects the driver file hcw85bda.sys), but just used a hex editor to replace the ID 0x64000200 by 0x60000200. > result is the same as described before, everything seems correct, but I have > some errors on dmesg and nothing is detected on scan (I must try with an > amplified antenna but I think it should detect something). certainly a good idea to use an amplified antenna. Have you got another DVB-t device that works with a passive antenna in the same area where you use your new device? > > Albert > -- -- Hans-Frieder Vogt e-mail: hfvogt <at> gmx .dot. net _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
