On Mittwoch, 13. Februar 2008, Eduard Huguet wrote: > Hi, > Here you have the dmesg output of "modprobe saa7134 i2c_scan=1": > > [ 773.619247] saa7133[0]: found at 0000:00:09.0, rev: 209, irq: 23, > latency: 64, mmio: 0xf7ffa800 > [ 773.619258] saa7133[0]: subsystem: 1461:a7a1, board: Avermedia A700 > [card=132,autodetected] > [ 773.619273] saa7133[0]: board init: gpio is 2f200 > [ 773.865218] saa7133[0]: i2c eeprom 00: 61 14 a1 a7 ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865270] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865312] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865351] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865393] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865433] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865459] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865702] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865727] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865753] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865780] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865810] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865840] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865868] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.865897] saa7133[0]: i2c eeprom e0: 00 01 81 af ea b5 ff ff ff ff > ff ff ff ff ff ff > [ 773.865923] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff > ff ff ff ff ff ff > [ 773.870157] saa7133[0]: i2c scan: found device @ 0x1c [???] > [ 773.883118] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] > [ 773.891907] saa7133[0]: registered device video0 [v4l2] > [ 773.892250] saa7133[0]: registered device vbi0 > [ 774.011780] zl1003x_attach: tuner initialization (Zarlink ZL10036 > addr=0x60) ok > [ 774.011805] DVB: registering new adapter (saa7133[0]) > [ 774.011819] DVB: registering frontend 0 (Zarlink ZL10313 DVB-S)... > > > These are the results of "lspci -vvnn" (after loading the driver): > > 00:09.0 Multimedia controller [0480]: Philips Semiconductors > SAA7133/SAA7135 Video Broadcast Decoder [1131:7133] (rev d1) > Subsystem: Avermedia Technologies Inc Unknown device [1461:a7a1] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 (63750ns min, 63750ns max) > Interrupt: pin A routed to IRQ 23 > Region 0: Memory at f7ffa800 (32-bit, non-prefetchable) [size=2K] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=3 PME- > Kernel driver in use: saa7134 > Kernel modules: saa7134 > added note about different gpio values and eeprom content to wiki. Regards Matthias -- Matthias Schwarzott (zzam) _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
