Yep, it's horrible. This is what I did, the adapters 0,1,2 are stillthere but MythTV is configured to used 4,5 and 6.
# My own DVB hell
# Twinhan DVB-S Card#KERNEL=="dvb[0-9].frontend0", ATTR{dev}=="212:3",symlink+="dvb/adapter4/frontend0", GROUP="video"KERNEL=="dvb[0-9].demux0", ATTR{dev}=="212:4",symlink+="dvb/adapter4/demux0", GROUP="video"KERNEL=="dvb[0-9].net0", ATTR{dev}=="212:7",symlink+="dvb/adapter4/net0", GROUP="video"KERNEL=="dvb[0-9].dvr0", ATTR{dev}=="212:5",symlink+="dvb/adapter4/dvr0", GROUP="video"## Nova-T Stick 1#KERNEL=="dvb[0-9].frontend0", ATTRS{serial}=="4030489593",symlink+="dvb/adapter5/frontend0", GROUP="video" KERNEL=="dvb[0-9].demux0", ATTRS{serial}=="4030489593",symlink+="dvb/adapter5/demux0", GROUP="video"KERNEL=="dvb[0-9].net0", ATTRS{serial}=="4030489593",symlink+="dvb/adapter5/net0", GROUP="video"KERNEL=="dvb[0-9].dvr0", ATTRS{serial}=="4030489593",symlink+="dvb/adapter5/dvr0", GROUP="video"## Nova-T Stick 2#KERNEL=="dvb[0-9].frontend0", ATTRS{serial}=="4027844315",symlink+="dvb/adapter6/frontend0", GROUP="video"KERNEL=="dvb[0-9].demux0", ATTRS{serial}=="4027844315",symlink+="dvb/adapter6/demux0", GROUP="video"KERNEL=="dvb[0-9].net0", ATTRS{serial}=="4027844315",symlink+="dvb/adapter6/net0", GROUP="video"KERNEL=="dvb[0-9].dvr0", ATTRS{serial}=="4027844315",symlink+="dvb/adapter6/dvr0", GROUP="video"
I'm not sure if gmail has split the lines above but each actual lineshould start with KERNEL.
Sim
On 07/02/2008, Eduard Huguet <eduardhc@xxxxxxxxx> wrote: > Hi,> I currently have a media center computer set up using Gentoo 64 bit> and a Hauppauge Nova-T 500 card (dual DVB-T receiver). Now I'm trying to> add a new card (DVB-S), and here my problems begin: not mentioning the > experimental state of the driver (this is a different story that doesn't> matter now), my problem is that the new card porks the order in which> the device nodes were created in /dev. And even worse, the actual order > ing schema is different between a cold boot and rebooting:>> Cold boot:> · DVB:0: DVB-S tuner from Avermedia A700> · DVB:1,2: DVB-T tuners from Nova-T>> Reboot:> · DVB:0: 1st DVB-T tuner from Nova-T > · DVB:1: DVB-S tuner from A700> · DVB:2: 2nd DVB-T tuner from Nova-T>> I guess that on a cold boot the Nova-T 500 takes longer to initialize> (due to the firmware being loaded), so its adaptors gets both created > later.>> Is there any way to avoid this? My MythTV setup currently expects to> find the 2 Nova-T 500 adaptors on DVB:0 and DVB:1, and In expected the> new DVB-S adaptor to be created as DVB:2. However, it seems this is not > the case.>> Is there any way to force the numbering schema or the 2 adaptors? ¿Would> maybe help i.e. setting RC_DEVICE_TARBALL="yes" in /etc/conf.d/rc> (currently is set to "no") with only the Nova-T connected and then > adding te other one? I wonder is this would force its adaptors to be> created always at the same position.>> Thanks for any help you could provide.>> Eduard>>> _______________________________________________ > linux-dvb mailing list> linux-dvb@xxxxxxxxxxx> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >_______________________________________________linux-dvb mailing listlinux-dvb@xxxxxxxxxxxxxxx://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
