I found some more information on this Twinhan card - there's a sticker on the card that changes the version number from VP-1022A VER 2.0, to 102g. I don't know if that's just a marketing change or what, but I now find more information using google about VP-1022A. There's a fairly long thread on this mailing list, in which a patch is posted here: http://www.linuxtv.org/pipermail/linux-dvb/2007-February/015866.html but then in a subsequent email the next day, the patch is retracted: http://www.linuxtv.org/pipermail/linux-dvb/2007-February/015872.html which says, "Scrap that patch I did! It only applies to some Twinhan cards. I spotted the fault "bttv0: Bt878 (rev 17) at 0000:00:0f.0, irq: 10, latency: 128, mmio: 0xde001000" You need to change your bios settings and change pci latency to 32. If Matthew Hagan still posts to this mailing list, do you still consider that to be the right fix for the 102g/VP-1022A? I will try this out. - Corey --- Corey Ashford <yeroca@xxxxxxxxx> wrote: > Date: Sat, 26 Jan 2008 23:14:11 -0800 (PST) > From: Corey Ashford <yeroca@xxxxxxxxx> > To: linux-dvb@xxxxxxxxxxx > Subject: Problem with Twinhan 102g not being recognized > > Hello, > > A little background first... > > I've recently switched over from using MyTheater on Windows to MythTV > under Fedora 8. I'm running the latest Fedora 8 kernel, 2.6.23.14-107. > Under Windows XP, I was able to use my Twinhan 102g card with the FTA > satellite antenna I have. However, under linux, it appears the card > is > not recognized properly. I actually have two bt878-based cards in my > system.. a Twinhan 3250 ATSC card which is recognized and is working > properly, and a Twinhan 102g which is not recognized completely. > > If I rmmod bttv, bt878, dvb_bt8xx, dst, and then /sbin/modprobe bttv, > I > get this: > > [corey@Family_Room log]# dmesg -c > bttv: driver version 0.9.17 loaded > bttv: using 8 buffers with 2080k (520 pages) each for capture > bttv: Bt8xx card found (0). > bttv0: Bt878 (rev 17) at 0000:02:0a.0, irq: 21, latency: 64, mmio: > 0xbfefe000 > bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID > is > 1822:000 > 1 > bttv0: using: Twinhan DST + clones [card=113,autodetected] > bttv0: gpio: en=00000000, out=00000000 in=00f36cff [init] > bttv0: tuner absent > bttv0: add subdevice "dvb0" > bttv: Bt8xx card found (1). > bttv1: Bt878 (rev 17) at 0000:02:0b.0, irq: 16, latency: 64, mmio: > 0xbfefc000 > bttv1: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID > is > 1822:000 > 1 > bttv1: using: Twinhan DST + clones [card=113,autodetected] > bttv1: gpio: en=00000000, out=00000000 in=00f5ffff [init] > bttv1: tuner absent > bttv1: add subdevice "dvb1" > bt878: AUDIO driver version 0.0.0 loaded > bt878: Bt878 AUDIO function found (0). > ACPI: PCI Interrupt 0000:02:0a.1[A] -> GSI 22 (level, low) -> IRQ 21 > bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB > functions. > bt878(0): Bt878 (rev 17) at 02:0a.1, irq: 21, latency: 64, memory: > 0xbfeff000 > bt878: Bt878 AUDIO function found (1). > ACPI: PCI Interrupt 0000:02:0b.1[A] -> GSI 23 (level, low) -> IRQ 16 > bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB > functions. > bt878(1): Bt878 (rev 17) at 02:0b.1, irq: 16, latency: 64, memory: > 0xbfefd000 > DVB: registering new adapter (bttv0) > dst(0) dst_get_device_id: Recognise [ATSCAD] > DST type flags : 0x10 firmware version = 2 > dst(0) dst_get_mac: MAC Address=[00:08:ca:16:cb:00] > dst(0) dst_get_tuner_info: DST TYpe = MULTI FE > dst(0) dst_get_tuner_info: DST type has TS=188 > dst(0) dst_fw_ver: Firmware Ver = 1.3 Build = 06, on 9:45, 1-3-2005 > dst(0) dst_card_type: Device Model=[VP32500] > dst(0) dst_get_vendor: Vendor=[TWINHAN] > DVB: registering frontend 0 (DST ATSC)... > DVB: registering new adapter (bttv1) > dst(1) dst_get_device_id: Recognise [DST-03T] > dst(1) dst_get_device_id: Unsupported > dst(1) dst_get_device_id: Unsupported > dst(1) dst_get_device_id: [DST-03T] has a [MB 86A15] > dst(1) dst_get_device_id: [DST-03T] has a [MB 86A15] > DST type flags : 0x2 ts204 0x4 symdiv 0x10 firmware version = 2 > dst(1) dst_get_mac: MAC Address=[00:08:ca:16:bc:00] > DVB: registering frontend 1 (DST DVB-S)... > > Besides the "Unsupported" error, my evidence that the card is not > working is that I cannot get any channels out of a scan. I know I > have > the right frequency, symbol rate, and polarity, etc. The card is > sort > of working, in that diseqc commands are making it to the rotor, but I > think the tuner is not recognized, so tuning in a stream simply does > not work. > > I tried doing the modprobe of the modules one at a time, but it > appears > that bttv is bringing in the other three modules automatically, and I > don't know how to add the "verbose" parameter when it does that. > > I've also tried > /sbin/modprobe bttv card=113 card=113 > but the driver seemed to ignore those options. > > Any suggestions would be appreciated. > > Thanks for your consideration, > > - Corey > > > > ____________________________________________________________________________________ > Never miss a thing. Make Yahoo your home page. > http://www.yahoo.com/r/hs > > _______________________________________________ > linux-dvb mailing list > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > ____________________________________________________________________________________ Never miss a thing. Make Yahoo your home page. http://www.yahoo.com/r/hs _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
