On Jan 23, 2008 7:29 PM, superhappyfunball <superhappyfunball@xxxxxxxxx> wrote: > Muppet Man wrote: > > > Ok, I did the sudo make rminstall and rm rf v4l-dvb, downloaded the > > file from the link, extracted, cd, sudo make, sudo make install, > > rebooted, and still had the same problem > > Indeed. I even made sure the old modules were completely wiped before I > installed a clean set of modules from mercurial. > > In short... > > [ 50.272060] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded > [ 50.272223] cx88[0]: subsystem: 11bd:0051, board: Pinnacle PCTV HD > 800i [card=58,autodetected] > [ 50.272294] cx88[0]: TV tuner type 76, Radio tuner type -1 > [ 50.418386] input: cx88 IR (Pinnacle PCTV HD 800i) as /class/input/input6 > [ 50.418494] cx88[0]/2: cx2388x 8802 Driver Manager > [ 50.418685] cx88[0]/2: found at 0000:02:02.2, rev: 5, irq: 18, > latency: 32, mmio: 0xf4000000 > [ 50.615427] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded > [ 50.615675] cx88[0]/0: found at 0000:02:02.0, rev: 5, irq: 18, > latency: 32, mmio: 0xf2000000 > [ 51.253871] cx88/2: cx2388x dvb driver version 0.0.6 loaded > [ 51.253935] cx88/2: registering cx8802 driver, type: dvb access: shared > [ 51.254792] cx88[0]/2: subsystem: 11bd:0051, board: Pinnacle PCTV HD > 800i [card=58] > [ 51.254861] cx88[0]/2: cx2388x based DVB/ATSC card > [ 52.343530] tuner' 0-0064: chip found @ 0xc8 (cx88[0]) > [ 52.375709] DVB: registering new adapter (cx88[0]) > [ 52.458249] Modules linked in: snd_mpu401 snd_mpu401_uart snd_emu10k1 > snd_ac97_codec ac97_bus snd_util_mem snd_seq_midi snd_hwdep > snd_seq_dummy s5h1409 snd_seq_oss tuner tea576$ > [ 52.465209] [<f8a1dbc0>] cx88_tuner_callback+0x0/0x60 [cx88xx] > [ 52.465537] [<f8a1fcee>] attach_inform+0xee/0x180 [cx88xx] > [ 52.465664] [<f8a1dbc0>] cx88_tuner_callback+0x0/0x60 [cx88xx] > [ 52.470649] cx88[0]/0: registered device video0 [v4l2] > [ 52.470759] cx88[0]/0: registered device vbi0 > [ 52.476241] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards > > > The only way I could get this dmesg output, was to boot off the recovery > kernel. Even under the recovery kernel, attempting to start or load X in > any way (kdm, gdm, or startx) results in a complete and utter > crash/freeze. You cannot get out of it without a system reset. You can't > even get into an alternate tty to kill the process. It just locks. > > I guess my question at this point is twofold: > > 1) is this, as Steve suggested earlier, a problem with core videobuf? Or > is it the nVidia driver? The hang point seems to be when nVidia gets > invoked and X Starts. kdm/gdm do not even seem to get a chance to load. > > 2) What, if anything can I do to get it to work, or help you guys figure > out where the problem is? I am open to being a guinea pig in any way I > can to help get this solved. =) > > The compile runs fine. The modules install fine. Something else is amiss. > Before we try anything else, I would like to rule out the obvious: Do you have the firmware for the xc5000 tuner in place? If not, then please download it from http://www.steventoth.net/linux/xc5000/ and extract the firmware using the script in the same location (see the readme file for instruction). I hope that will resolve the issue. If you have indeed put the firmware in place for your previous tests, would you please post the *full* output of dmesg? You can post that at pastebin.com and just send the link in the email. -- Chaogui Zhang _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
