----- Original Message ----
From: superhappyfunball <superhappyfunball@xxxxxxxxx>
To: Muppet Man <muppetman4662@xxxxxxxxx>
Cc: Chaogui Zhang <czhang1974@xxxxxxxxx>; linux-dvb@xxxxxxxxxxx
Sent: Wednesday, January 23, 2008 6:29:47 PM
Subject: Re: Pinnacle 800i driver problems
Muppet Man wrote:
> Ok, I did the sudo make rminstall and rm rf v4l-dvb, downloaded the
> file from the link, extracted, cd, sudo make, sudo make install,
> rebooted, and still had the same problem
Indeed. I even made sure the old modules were completely wiped before I
installed a clean set of modules from mercurial.
In short...
[ 50.272060] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
[ 50.272223] cx88[0]: subsystem: 11bd:0051, board: Pinnacle PCTV HD
800i [card=58,autodetected]
[ 50.272294] cx88[0]: TV tuner type 76, Radio tuner type -1
[ 50.418386] input: cx88 IR (Pinnacle PCTV HD 800i) as /class/input/input6
[ 50.418494] cx88[0]/2: cx2388x 8802 Driver Manager
[ 50.418685] cx88[0]/2: found at 0000:02:02.2, rev: 5, irq: 18,
latency: 32, mmio: 0xf4000000
[ 50.615427] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
[ 50.615675] cx88[0]/0: found at 0000:02:02.0, rev: 5, irq: 18,
latency: 32, mmio: 0xf2000000
[ 51.253871] cx88/2: cx2388x dvb driver version 0.0.6 loaded
[ 51.253935] cx88/2: registering cx8802 driver, type: dvb access: shared
[ 51.254792] cx88[0]/2: subsystem: 11bd:0051, board: Pinnacle PCTV HD
800i [card=58]
[ 51.254861] cx88[0]/2: cx2388x based DVB/ATSC card
[ 52.343530] tuner' 0-0064: chip found @ 0xc8 (cx88[0])
[ 52.375709] DVB: registering new adapter (cx88[0])
[ 52.458249] Modules linked in: snd_mpu401 snd_mpu401_uart snd_emu10k1
snd_ac97_codec ac97_bus snd_util_mem snd_seq_midi snd_hwdep
snd_seq_dummy s5h1409 snd_seq_oss tuner tea576$
[ 52.465209] [<f8a1dbc0>] cx88_tuner_callback+0x0/0x60 [cx88xx]
[ 52.465537] [<f8a1fcee>] attach_inform+0xee/0x180 [cx88xx]
[ 52.465664] [<f8a1dbc0>] cx88_tuner_callback+0x0/0x60 [cx88xx]
[ 52.470649] cx88[0]/0: registered device video0 [v4l2]
[ 52.470759] cx88[0]/0: registered device vbi0
[ 52.476241] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
The only way I could get this dmesg output, was to boot off the recovery
kernel. Even under the recovery kernel, attempting to start or load X in
any way (kdm, gdm, or startx) results in a complete and utter
crash/freeze. You cannot get out of it without a system reset. You can't
even get into an alternate tty to kill the process. It just locks.
I guess my question at this point is twofold:
1) is this, as Steve suggested earlier, a problem with core videobuf? Or
is it the nVidia driver? The hang point seems to be when nVidia gets
invoked and X Starts. kdm/gdm do not even seem to get a chance to load.
2) What, if anything can I do to get it to work, or help you guys figure
out where the problem is? I am open to being a guinea pig in any way I
can to help get this solved. =)
The compile runs fine. The modules install fine. Something else is amiss.
Christopher.
--
"Do not taunt Happy Fun Ball"
superhappyfunball@xxxxxxxxx
"You fiend! Never have I encountered such corrupt and foul-minded
perversity! Have you ever considered a career in the church?" -- Bishop
of Bath and Wells
Wow,
You went way, way over my head with the start up and stuff like that. I basically turned my computer on, walked away for 15 minutes. Anywho, I would be willing to be a test subject also, but I am rather new to the linux thing, and very new to the driver compiling.
Ed
From: superhappyfunball <superhappyfunball@xxxxxxxxx>
To: Muppet Man <muppetman4662@xxxxxxxxx>
Cc: Chaogui Zhang <czhang1974@xxxxxxxxx>; linux-dvb@xxxxxxxxxxx
Sent: Wednesday, January 23, 2008 6:29:47 PM
Subject: Re: Pinnacle 800i driver problems
Muppet Man wrote:
> Ok, I did the sudo make rminstall and rm rf v4l-dvb, downloaded the
> file from the link, extracted, cd, sudo make, sudo make install,
> rebooted, and still had the same problem
Indeed. I even made sure the old modules were completely wiped before I
installed a clean set of modules from mercurial.
In short...
[ 50.272060] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
[ 50.272223] cx88[0]: subsystem: 11bd:0051, board: Pinnacle PCTV HD
800i [card=58,autodetected]
[ 50.272294] cx88[0]: TV tuner type 76, Radio tuner type -1
[ 50.418386] input: cx88 IR (Pinnacle PCTV HD 800i) as /class/input/input6
[ 50.418494] cx88[0]/2: cx2388x 8802 Driver Manager
[ 50.418685] cx88[0]/2: found at 0000:02:02.2, rev: 5, irq: 18,
latency: 32, mmio: 0xf4000000
[ 50.615427] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
[ 50.615675] cx88[0]/0: found at 0000:02:02.0, rev: 5, irq: 18,
latency: 32, mmio: 0xf2000000
[ 51.253871] cx88/2: cx2388x dvb driver version 0.0.6 loaded
[ 51.253935] cx88/2: registering cx8802 driver, type: dvb access: shared
[ 51.254792] cx88[0]/2: subsystem: 11bd:0051, board: Pinnacle PCTV HD
800i [card=58]
[ 51.254861] cx88[0]/2: cx2388x based DVB/ATSC card
[ 52.343530] tuner' 0-0064: chip found @ 0xc8 (cx88[0])
[ 52.375709] DVB: registering new adapter (cx88[0])
[ 52.458249] Modules linked in: snd_mpu401 snd_mpu401_uart snd_emu10k1
snd_ac97_codec ac97_bus snd_util_mem snd_seq_midi snd_hwdep
snd_seq_dummy s5h1409 snd_seq_oss tuner tea576$
[ 52.465209] [<f8a1dbc0>] cx88_tuner_callback+0x0/0x60 [cx88xx]
[ 52.465537] [<f8a1fcee>] attach_inform+0xee/0x180 [cx88xx]
[ 52.465664] [<f8a1dbc0>] cx88_tuner_callback+0x0/0x60 [cx88xx]
[ 52.470649] cx88[0]/0: registered device video0 [v4l2]
[ 52.470759] cx88[0]/0: registered device vbi0
[ 52.476241] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
The only way I could get this dmesg output, was to boot off the recovery
kernel. Even under the recovery kernel, attempting to start or load X in
any way (kdm, gdm, or startx) results in a complete and utter
crash/freeze. You cannot get out of it without a system reset. You can't
even get into an alternate tty to kill the process. It just locks.
I guess my question at this point is twofold:
1) is this, as Steve suggested earlier, a problem with core videobuf? Or
is it the nVidia driver? The hang point seems to be when nVidia gets
invoked and X Starts. kdm/gdm do not even seem to get a chance to load.
2) What, if anything can I do to get it to work, or help you guys figure
out where the problem is? I am open to being a guinea pig in any way I
can to help get this solved. =)
The compile runs fine. The modules install fine. Something else is amiss.
Christopher.
--
"Do not taunt Happy Fun Ball"
superhappyfunball@xxxxxxxxx
"You fiend! Never have I encountered such corrupt and foul-minded
perversity! Have you ever considered a career in the church?" -- Bishop
of Bath and Wells
Wow,
You went way, way over my head with the start up and stuff like that. I basically turned my computer on, walked away for 15 minutes. Anywho, I would be willing to be a test subject also, but I am rather new to the linux thing, and very new to the driver compiling.
Ed
Never miss a thing. Make Yahoo your homepage.
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
