The decoder/bridge IC reads "saa7133HL/101"
The 18 pin IC reads
"A T8P56S
HBIHG 709"
After running lshal I got
udi = '/org/freedesktop/Hal/devices/pci_1131_7133'
info.bus = 'pci' (string)
info.linux.driver = 'saa7134' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_10de_26f' (string)
info.product = 'SAA7133/SAA7135 Video Broadcast Decoder' (string)
info.subsystem = 'pci' (string)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:10.0/0000:04:08.0'
(string)
pci.device_class = 4 (0x4) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:10.0/0000:04:08.0' (string)
pci.product = 'SAA7133/SAA7135 Video Broadcast Decoder' (string)
pci.product_id = 28979 (0x7133) (int)
pci.subsys_product_id = 26224 (0x6670) (int)
pci.subsys_vendor = 'LeadTek Research Inc.' (string)
pci.subsys_vendor_id = 4221 (0x107d) (int)
pci.vendor = 'Philips Semiconductors' (string)
pci.vendor_id = 4401 (0x1131) (int)
And running dmesg produced
saa7133[0]: found at 0000:04:08.0, rev: 16, irq: 19, latency: 64, mmio:
0xfeaff800
saa7133[0]: subsystem: 107d:6670, board: UNKNOWN/GENERIC
[card=0,autodetected]
saa7133[0]: board init: gpio is a022000
saa7133[0]: i2c eeprom 00: 7d 10 70 66 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: 00 ff 82 0e ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 02 ff 01 04 08 ff 00 a8 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 18 00 c2 86 00 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
I installed this card as if it were the kworld 110 and it works great. I
added
" alias char-major-81 videodev
alias char-major-81-0 saa7134
options saa7134 card=90 "
to modprobe.conf and downloaded the nxt2004 firmware.
I don't have cable and I passed on trying to
get the remote to work. I also didn't try very
hard to get the analog tuner to work. I hope this info helps.
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
