O&M Ugarcina wrote: > Hello Guys, > > I just purchased a Compro Videomate S350 satellite card with the > intention of using it in mythtv . After installing the card I was > surprised to find that it was not being recognized . This is the out > put of my dmesg : > > saa7130[0]: found at 0000:04:01.0, rev: 1, irq: 21, latency: 64, mmio: > 0xfeaffc00 > saa7130[0]: subsystem: 185b:c900, board: UNKNOWN/GENERIC > This (according to the subsystem ID) looks like a clone of Compro VideoMate DVB-T300, which should be autodetected in recent kernels. Could you please try retesting with linux-2.6.23? -- Hello Alexander, I just tried it with kernel : [root@localhost mythtv]# uname -r 2.6.23-5.fc8 dmesg looks like this : saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 22 (level, low) -> IRQ 21 saa7130[0]: found at 0000:04:01.0, rev: 1, irq: 21, latency: 64, mmio: 0xfeaffc00 saa7130[0]: subsystem: 185b:c900, board: UNKNOWN/GENERIC [card=0,autodetected] saa7130[0]: board init: gpio is 843f00 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 saa7130[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7130[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00 87 ff ff ff ff saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 40: ff d6 00 c0 86 1c 02 01 02 ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff cb saa7130[0]: i2c eeprom 60: 30 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 70: 00 00 00 10 03 9c ff ff ff ff ff ff ff ff ff ff saa7130[0]: registered device video0 [v4l2] saa7130[0]: registered device vbi0 Much thanks for your reply Milorad Alexander E. Patrakov Alexander E. Patrakov wrote: > O&M Ugarcina wrote: >> [root@localhost mythtv]# uname -r >> 2.6.23-5.fc8 >> saa7130[0]: subsystem: 185b:c900, board: UNKNOWN/GENERIC >> [card=0,autodetected] > > This simply can't be true. 185b:c900 is a T-300, not an unknown board. > See > http://www.linuxtv.org/hg/v4l-dvb/file/7dba1f554c4a/linux/Documentation/video4linux/CARDLIST.saa7134 > > > Try creating the file /etc/modprobe.d/compro with the following line > in it: > > options saa7134 card=70 > > and rebooting. > Hello Alexander, I have implemented the above config and we have progressed a bit further . This is again with kernel : [root@localhost mythtv]# uname -r 2.6.23-5.fc8 my dmesg is now a little better and looks like : Linux video capture interface: v2.00 PCI: Enabling device 0000:00:1f.3 (0001 -> 0003) ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 20 saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 22 (level, low) -> IRQ 21 saa7130[0]: found at 0000:04:01.0, rev: 1, irq: 21, latency: 64, mmio: 0xfeaffc00 saa7130[0]: subsystem: 185b:c900, board: Compro Videomate DVB-T300 [card=70,insmod option] saa7130[0]: board init: gpio is 843f00 input: saa7134 IR (Compro Videomate DV as /class/input/input4 sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 2:0:0:0: Attached scsi generic sg1 type 5 sd 4:0:0:0: Attached scsi generic sg2 type 0 sd 4:0:0:1: Attached scsi generic sg3 type 0 sd 4:0:0:2: Attached scsi generic sg4 type 0 sd 4:0:0:3: Attached scsi generic sg5 type 0 cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded cx2388x v4l2 driver version 0.0.6 loaded Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 saa7130[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7130[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00 87 ff ff ff ff saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 40: ff d6 00 c0 86 1c 02 01 02 ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff cb saa7130[0]: i2c eeprom 60: 30 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7130[0]: i2c eeprom 70: 00 00 00 10 03 9c ff ff ff ff ff ff ff ff ff ff tuner 1-0068: chip found @ 0xd0 (saa7130[0]) saa7130[0]: registered device video0 [v4l2] saa7130[0]: registered device vbi0 CORE cx88[0]: subsystem: 18ac:db10, board: DViCO FusionHDTV DVB-T Plus [card=21,autodetected] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe saa7130[0]/dvb: frontend initialization failed Please ignore the references to cx88 as this is coming from my Dvico fusion DVBT card which is working perfectly . So it looks like most of T300's config is usable for my card ( a S350 , s-for satellite) except the frontend which I guess needs to be satellite specific for LNB control as well as diseqc functionality . Where do we go from here ? Best Regards Milorad _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
