My problem is I cannot get usb reenumeration with one of my two usb adapters. On same phisical usb port with Hauppauge Nova-T-USB2 is all ok:
/: Bus 04.Port 1: Dev 1, Class=root_hub, Drv=ehci_hcd/6p, 480M
|_ Port 2: Dev 14, If 0, Prod=SOHO-FX2, Class=vend.,
Drv=dvb_usb_nova_t_usb2, 480M
/: Bus 03.Port 1: Dev 1, Class=root_hub, Drv=ohci_hcd/2p, 12M
/: Bus 02.Port 1: Dev 1, Class=root_hub, Drv=ohci_hcd/2p, 12M
|_ Port 2: Dev 2, If 0, Prod=8-in-2, Class=stor.,
Drv=usb-storage, 12M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Drv=ohci_hcd/2p, 12M
and
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 4-2: new high speed USB device using ehci_hcd and address 14
usb 4-2: configuration #1 chosen from 1 choice
dvb-usb: found a 'Hauppauge WinTV-NOVA-T usb2' in warm state.
**WARNING** I2C adapter driver [Hauppauge WinTV-NOVA-T usb2] forgot to specify physical device; fix it!
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Hauppauge WinTV-NOVA-T usb2).
dvb-usb: MAC address: 00:0d:fe:04:61:67
**WARNING** I2C adapter driver [DiBX000 tuner I2C bus] forgot to specify physical device; fix it!
DVB: registering frontend 0 (DiBcom 3000MC/P)...
input: IR-receiver inside an USB DVB receiver as /class/input/input10
dvb-usb: schedule remote query interval to 100 msecs.
dvb-usb: Hauppauge WinTV-NOVA-T usb2 successfully initialized and connected.
and whith Hauppauge Nova-T Stick on the SAME port:
/: Bus 04.Port 1: Dev 1, Class=root_hub, Drv=ehci_hcd/6p, 480M
/: Bus 03.Port 1: Dev 1, Class=root_hub, Drv=ohci_hcd/2p, 12M
/: Bus 02.Port 1: Dev 1, Class=root_hub, Drv=ohci_hcd/2p, 12M
|_ Port 1: Dev 5, If 0, Prod=Nova-T Stick, Class=vend.,
Drv=none, 12M
|_ Port 2: Dev 2, If 0, Prod=8-in-2, Class=stor.,
Drv=usb-storage, 12M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Drv=ohci_hcd/2p, 12M
an dmesg:
usb 2-1: new full speed USB device using ohci_hcd and address 5
usb 2-1: not running at top speed; connect to a high speed hub
usb 2-1: configuration #1 chosen from 1 choice
dvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
**WARNING** I2C adapter driver [Hauppauge Nova-T Stick] forgot to specify physical device; fix it!
dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter)
dvb-usb: Hauppauge Nova-T Stick error while loading driver (-19)
Hardware is MSI MEGA PC 651:
http://global.msi.com.tw/index.php?func=proddesc&prod_no=39&maincat_no=134&cat2_no=264&cat3_no=306
Kernel is: 2.6.20-1.2944.fc6 on Mythdora 4
Hope someone can help me.
Thx
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
