I've recently bought a couple of MSI Mega Sky 580s (identified as MSI Mega Sky 55801) but I can't get them to scan or tune. I've pulled the latest version of the v4l-dvb repository, compiled and installed without any problems. On plugging the stick in I get the following (promising) dmesg output: usb 5-5: new high speed USB device using ehci_hcd and address 6 usb 5-5: configuration #1 chosen from 1 choice input: PC-DTV Receiver PC-DTV Receiver as /class/input/input6 input: USB HID v1.01 Keyboard [PC-DTV Receiver PC-DTV Receiver] on usb-0000:00:1d.7-5 dvb-usb: found a 'MSI Mega Sky 55801 DVB-T USB2.0' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (MSI Mega Sky 55801 DVB-T USB2.0) DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... Quantek QT1010 successfully identified. dvb-usb: MSI Mega Sky 55801 DVB-T USB2.0 successfully initialized and connected. usbcore: registered new interface driver dvb_usb_gl861 I note that this device is always reported as being in a 'warm state', I assume this means that no firmware is required. However when attempting to scan I just get: [root@localhost]# scandvb /usr/share/dvb-apps/dvb-t/uk-Mendip > channels.conf scanning /usr/share/dvb-apps/dvb-t/uk-Mendip using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 754167000 0 2 9 1 0 0 0 >>> tune to: 754167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_16:TRANSMISSION_MODE_2K:GUARD_INTERVAL_1_32:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: 754167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_16:TRANSMISSION_MODE_2K:GUARD_INTERVAL_1_32:HIERARCHY_NONE (tuning failed) WARNING: >>> tuning failed!!! ERROR: initial tuning failed dumping lists (0 services) Done. Also, if I try to tune using a channels.conf file generated by a (working) CinergyT2 in the same system I just get: [root@localhost]# tzap -a 0 "BBC ONE" using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' tuning to 778166670 Hz video pid 0x0258, audio pid 0x0259 status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 3794 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 37c8 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 369c | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 3704 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 3860 | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 3690 | snr 0000 | ber 00000000 | unc 00000000 | Any help would be greatly appreciated! Stephen _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
