Hello! Thank you for the quick hint! I have downloaded and compiled the v4l drivers rom the mercruial-repo. If i set the USB_PID_MSI_DIGI_VOX_MINI_II to 0x0506 i get following dmesg: [ 340.530811] usb 6-3: new high speed USB device using ehci_hcd and address 8 [ 340.645215] PM: Adding info for usb:6-3 [ 340.645315] PM: Adding info for No Bus:usbdev6.8_ep00 [ 340.645345] usb 6-3: configuration #1 chosen from 1 choice [ 340.645456] PM: Adding info for usb:6-3:1.0 [ 340.645548] PM: Adding info for No Bus:usbdev6.8 [ 340.705639] dvb-usb: found a 'MSI DIGI VOX mini II DVB-T USB2.0' in warm state. [ 340.706061] PM: Adding info for No Bus:i2c-4 [ 340.706379] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 340.710602] DVB: registering new adapter (MSI DIGI VOX mini II DVB-T USB2.0) [ 342.724107] dvb-usb: no frontend was attached by 'MSI DIGI VOX mini II DVB-T USB2.0' [ 342.724116] dvb-usb: MSI DIGI VOX mini II DVB-T USB2.0 successfully initialized and connected. [ 342.724293] PM: Adding info for No Bus:usbdev6.8_ep01 [ 342.724562] PM: Adding info for No Bus:usbdev6.8_ep81 [ 342.724770] PM: Adding info for No Bus:usbdev6.8_ep02 [ 342.724971] PM: Adding info for No Bus:usbdev6.8_ep04 [ 342.725169] PM: Adding info for No Bus:usbdev6.8_ep86 [ 342.725371] PM: Adding info for No Bus:usbdev6.8_ep88 [ 344.722448] dvb_usb_m920x: probe of 6-3:1.0 failed with error -110 [ 344.722480] usbcore: registered new interface driver dvb_usb_m920x [ 393.785987] usb 6-4.3: reset high speed USB device using ehci_hcd and address 4 [ 393.873747] PM: Removing info for No Bus:usbdev6.4_ep01 [ 393.873807] PM: Removing info for No Bus:usbdev6.4_ep82 [ 393.874415] PM: Adding info for No Bus:usbdev6.4_ep01 [ 393.874478] PM: Adding info for No Bus:usbdev6.4_ep82 [ 413.759894] usb 6-4.3: reset high speed USB device using ehci_hcd and address 4 [ 413.847708] PM: Removing info for No Bus:usbdev6.4_ep01 [ 413.847779] PM: Removing info for No Bus:usbdev6.4_ep82 [ 413.848312] PM: Adding info for No Bus:usbdev6.4_ep01 [ 413.848378] PM: Adding info for No Bus:usbdev6.4_ep82 [ 447.705736] usb 6-4.3: reset high speed USB device using ehci_hcd and address 4 [ 447.793494] PM: Removing info for No Bus:usbdev6.4_ep01 [ 447.793558] PM: Removing info for No Bus:usbdev6.4_ep82 [ 447.794138] PM: Adding info for No Bus:usbdev6.4_ep01 [ 447.794187] PM: Adding info for No Bus:usbdev6.4_ep82 this continues... to reset and restart the folder /dev/dvb/adapter0/ is created anyway. #dvbscan --> Failed to open frontend In case of "define USB_PID_LIFEVIEW_TV_WALKER_TWIN_COLD 0x0506" the cpu-load goes up for about 30 seconds, but i was unable to get the dmesg, bec. my keyboard somehow get locked (no response on any keypress, even numlock was disfunct). With USB_PID_DPOSH_M9206_COLD set to 0x0506 it seems not to work at all... dmesg after plugging in: [ 283.191498] usb 6-3: new high speed USB device using ehci_hcd and address 9 [ 283.306767] PM: Adding info for usb:6-3 [ 283.306878] PM: Adding info for No Bus:usbdev6.9_ep00 [ 283.306909] usb 6-3: configuration #1 chosen from 1 choice [ 283.307003] PM: Adding info for usb:6-3:1.0 [ 283.307095] PM: Adding info for No Bus:usbdev6.9 I have done a first quick dvb-snoop on Windows XP (running in a VMWare). The log contains the plugin of the COLD device, it seems to get some commands, then replugs as the hot (0x0500 as far as i can see). The logfile: http://nopaste.info/eead046817.html Firmware: I did not get any hint (by dmesg), which (or if at all) firmware is sent to the stick... how can i debug this? Or where is it defined, which FW is send to whom? TIA Daniel Weigl Am Mon, 18 Jun 2007 01:54:08 +0200 hat Nick Andrew <nick-linuxtv@xxxxxxxxxxxxxxx> geschrieben: > On Sun, Jun 17, 2007 at 09:56:37PM +0200, Daniel Weigl wrote: >> For now i was not able to find the according site on lifeview.com. >> Optical >> it looks ident to the "TV Walker Q2" >> [ http://www.lifeview.com.tw/html/products/external_tv/tv_walker_q2.htm >> ], >> but mine is labeled as "LR506". >> >> Some informations: >> lsusb: >> "Bus 006 Device 013: ID 10fd:0506 Anubis Electronics, Ltd" > > Hmm, try latest v4l-dvb repository (from hg). Modules dvb_usb_m920x, > tda827x, tda1004x. Modify linux/drivers/media/dvb/dvb-usb/dvb-usb-ids.h > to change one of the following lines to 0x0506 and build, insmod and > see what happens: > > #define USB_PID_LIFEVIEW_TV_WALKER_TWIN_COLD 0x0514 > #define USB_PID_MSI_DIGI_VOX_MINI_II 0x1513 > #define USB_PID_DPOSH_M9206_COLD 0x9206 > > You may need to obtain a copy of your device's firmware. > > Nick. > > _______________________________________________ > linux-dvb mailing list > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb -- Erstellt mit Operas revolutionärem E-Mail-Modul: http://www.opera.com/mail/ _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
