I have the same issues with the same card. Benjie Gillam. arph@xxxxxxx wrote:
hello, after plugin the freecom 25451 rev3 i can see this dmesg-output: [ 136.488000] usb 5-3: new high speed USB device using ehci_hcd and address 4 [ 136.628000] usb 5-3: configuration #1 chosen from 1 choice [ 136.760000] dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in cold state, will try to load a firmware [ 136.772000] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-fc03.fw' [ 136.860000] usbcore: registered new interface driver dvb_usb_dtt200u [ 138.260000] usb 5-3: USB disconnect, address 4 [ 138.260000] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. [ 139.508000] usb 5-3: new high speed USB device using ehci_hcd and address 5 [ 139.640000] usb 5-3: configuration #1 chosen from 1 choice [ 139.640000] dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in warm state. [ 139.640000] dvb-usb: will use the device's hardware PID filter (table count: 15). [ 139.644000] DVB: registering new adapter (WideView WT-220U PenType Receiver (Typhoon/Freecom)). [ 139.644000] DVB: registering frontend 0 (WideView USB DVB-T)... [ 139.644000] input: IR-receiver inside an USB DVB receiver as /class/input/input9 [ 139.644000] dvb-usb: schedule remote query interval to 300 msecs. [ 139.644000] dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) successfully initialized and connected. [ 139.644000] dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in warm state. [ 139.644000] dvb-usb: will use the device's hardware PID filter (table count: 15). [ 139.644000] DVB: registering new adapter (WideView WT-220U PenType Receiver (Typhoon/Freecom)). [ 139.644000] DVB: registering frontend 1 (WideView USB DVB-T)... [ 139.644000] input: IR-receiver inside an USB DVB receiver as /class/input/input10 [ 139.644000] dvb-usb: schedule remote query interval to 300 msecs. [ 139.644000] dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) successfully initialized and connected. [ 139.816000] usbcore: registered new interface driver hiddev [ 139.816000] usbcore: registered new interface driver usbhid [ 139.816000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 139.832000] usbcore: registered new interface driver xpad [ 139.832000] drivers/usb/input/xpad.c: driver for Xbox controllers v0.1.6 [ 141.244000] eth1: no IPv6 routers present [ 141.944000] dvb-usb: recv bulk message failed: -110 in kaffeine there are also 2 devices shown, but i think i only should have one of it? Can somebody explain this to me please. Also in kaffeine, when starting tv the first time, tv-screen freezes after 2 seconds and i have to switch to another channel, i think it is some problem with the firmware, because i also have a yakumo and everthing is fine. _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
