I have two DVB devices but one of these fails to initialise after I update my FC6 kernel, I'm pretty sure its the Air2PC/AirStar 2 DVB-T PCI card. I have regressed back to kernel.i686 2.6.19-1.2911.6.5.fc6 which brings my devices back online. I have pasted the /var/log/dmesg output for both working and broken kernel below The most interesting message is : **WARNING** I2C adapter driver [B2C2 FlexCop device] forgot to specify physical device; fix it! Any hints on what this means and if this can be fixed? or do I need to make some changes in my modules.conf?? Thanks FC6 Kernel 2911 (working) b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 20 DVB: registering new adapter (FlexCop Digital TV device). b2c2-flexcop: MAC address = 00:d0:d7:0a:33:62 ieee1394: Initialized config rom entry `ip1394' b2c2-flexcop: i2c master_xfer failed cx2388x v4l2 driver version 0.0.6 loaded b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: found the mt352 at i2c address: 0x0f DVB: registering frontend 0 (Zarlink MT352 DVB-T)... b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete FC6 Kernel 2933: (not working) b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully Linux video capture interface: v2.00 cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded /8] CORE cx88[0]: subsystem: 1822:0025, board: digitalnow DNTV Live! DVB-T Pro [card=42,insmod option] TV tuner 63 at 0x1fe, Radio tuner -1 at 0x1fe cx2388x v4l2 driver version 0.0.6 loaded input: cx88 IR (digitalnow DNTV Live! as /class/input/input4 cx88[0]/2: cx2388x 8802 Driver Manager cx88[0]/2: found at 0000:01:08.2, rev: 5, irq: 21, latency: 32, mmio: 0xf6000000 flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 DVB: registering new adapter (FlexCop Digital TV device). b2c2-flexcop: MAC address = 00:d0:d7:0a:33:62 **WARNING** I2C adapter driver [B2C2 FlexCop device] forgot to specify physical device; fix it! b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: i2c master_xfer failed b2c2-flexcop: found the mt352 at i2c address: 0x0f DVB: registering frontend 0 (Zarlink MT352 DVB-T)... b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
