Andreas Vinsander wrote: > Hi! > > I recently subscribed to this maillist and have since done some reading > up on the posts. And found this from the "Mantis > VP-1027/VP-1033/VP-1034/VP-2033/VP-3033"-thread: > Sorry for the late reply .. > -------------- > Subject: Re: Mantis VP-1027/VP-1033/VP-1034/VP-2033/VP-3033 > From: Manu Abraham > Date: Sat, 07 Oct 2006 05:11:49 -0700 > > Lauri Tischler wrote: >> >> Does this apply also to these cards >> - Twinhan DTV TER-CI 3030 Mantis DVB-T >> - Twinhan DTV TER-CI 3040 DVB-T PCI >> - Twinhan DTV SAT-CI 1030 DVB-S PCI > > No. The dst module supports these cards. Apologies, a mistake from my side. The 3030 Mantis DVB-T is a Mantis based card. Sorry for that stupid mistake. > > Manu > ---------------- > > I have one of those Twinhan DTV TER-CI 3030 Mantis DVB-T pci cards, but > the dst module (from gentoo package v4l-dvb-hg-0.1-r2, which seems to > pull the source via hg from the dvb repository) doesn't seem to > recognize the card. dmesg and logfiles shows that the modules are loaded > but they don't find a bt8x8 chip and thus no /dev/dvb/ entries are > created (udev-103). I have tried the modules supplied by the kernel > gentoo-sources-2.6.18-r2 (do I need to try vanilla 2.6.19-rc5?) as well, > with the same results. > > I am running 64bit Linux on an Athlon64 X2 3800+ stuffed into an ASUS > M2NPV-VM motherboard. Both PCI slots are used, one for the Twinhan card > and the other for an atheros based WiFi card (which works alright btw). > > I provide some lspci & pcimodules output down below, what else can I do > to find out what goes wrong here? Is it possible that Manu missed > something when he stated that this card was supported by the dst module? > > > # lspci -vv > ... > 04:08.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV PCI > Bridge Controller [Ver 1.0] (rev 01) > Subsystem: Twinhan Technology Co. Ltd Unknown device 0024 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (2000ns min, 63750ns max) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at fdaff000 (32-bit, prefetchable) [size=4K] This is a Mantis based card supported by the Mantis driver and not the dst. > > ... > > # lspci -nv > 04:08.0 0480: 1822:4e35 (rev 01) > Subsystem: 1822:0024 > Flags: bus master, medium devsel, latency 32, IRQ 5 > Memory at fdaff000 (32-bit, prefetchable) [size=4K] > > # pcimodules > nvidia > i2c-nforce2 > snd-hda-intel > ath_pci > > No sign of any DVB drivers compliant with the card at 04:08.0 > This card VP-3030 would use the MT352 driver rather than the ZL10353 driver as compared to the VP-3033 > I have quite good programming skills (C++, C) and would be happy to help > out as much as my wife allows me ;-) > > BR, > /Andreas Regards, Manu _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
