Re: Mantis VP-1027/VP-1033/VP-1034/VP-2033/VP-3033

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Michel,

Michel Verbraak wrote:
> Manu,
> 
> Thanks for the first preview.
> 
> I compiled the driver without problems, only the know dvb_net problem on
> FC5 kernel 2.6.17.
> As Jens allready wrote I had to copy the cu1216.ko module by hand to the
> right modules location.
> 
> I have a VP-1034.
> 
> A modprobe mantis gives me the following in dmesg:
> 
> ACPI: PCI Interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 217
> Mantis Rev 1, irq: 217, latency: 64
> memory: 0xf7eff000, mmio: 0xf8902000
> get_mac_address (1): MAC Address=[00:08:ca:19:9f:0b]
> get_subvendor_id (1): Sub Vendor ID=[0x1822]
> get_subdevice_id (1): Sub Device ID=[0x0014]
> mantis_alloc_buffers (1): DMA=0x32ce0000 cpu=0xf2ce0000 size=65536
> mantis_alloc_buffers (1): RISC=0xec51000 cpu=0xcec51000 size=1000
> DVB: registering new adapter (Mantis dvb adapter).
> mantis_frontend_init (1): Probing for MB86A16 (DVB-S/DSS)
> mantis_frontend_init (1): found MB86A16 DVB-S/DSS frontend @0x08
> DVB: registering frontend 0 (Fujitsu MB86A16 DVB-S)...
> 
> It created the /dev/dvb/adapter0/(demux0 & dvr0 & frontend0 & net0)
> devices.
> 

Sounds fine till here

> lspci -vv gives
> 02:0d.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV PCI
> Bridge Controller [Ver 1.0] (rev 01)
>        Subsystem: Twinhan Technology Co. Ltd Unknown device 0014
>        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
>        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>        Latency: 64 (2000ns min, 63750ns max)
>        Interrupt: pin A routed to IRQ 217
>        Region 0: Memory at f7eff000 (32-bit, prefetchable) [size=4K]
> 

You will need to update to the latest PCI ID 's for lspci to show the rest.
http://pciids.sourceforge.net/pci.ids

> I will try to test it with different programs.
> Does the driver also handle a diseqc motor ?

It supports diseqc , in it's current state, but needs testing. I haven't
tested the diseqc code on the 1034.



Regards,
Manu

_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[Index of Archives]     [Linux Media]     [Video 4 Linux]     [Asterisk]     [Samba]     [Xorg]     [Xfree86]     [Linux USB]

  Powered by Linux