>> I seen that MB86A15 on a card. But how can it help me to set up >> /dev/dvb/adapter0/frontend0 ? >> What the module should I insert? > modprobe dst verbose=4 > modprobe dvb-bt8xx Just a report I spend a day today to bring up it on a work place where PC connected to satellite dish, but it was unsuccessfull... weirdly Tonight I compile it on my home PC (no sat dish :(, only Twinhan 1025 card), so today I didn't get a video signal, hope to receive it tomorrow... Well I got the devices: root@fnm-desktop:/dev/dvb/adapter0# uname -a Linux fnm-desktop 2.6.18-rc4-dvb #1 PREEMPT Wed Aug 16 22:33:35 EEST 2006 i686 GNU/Linux root@fnm-desktop:/dev/dvb/adapter0# ls -al total 0 drwxr-xr-x 2 root root 120 Aug 16 22:56 . drwxr-xr-x 3 root root 60 Aug 16 22:56 .. crw-rw---- 1 root video 212, 4 Aug 16 22:56 demux0 crw-rw---- 1 root video 212, 5 Aug 16 22:56 dvr0 crw-rw---- 1 root video 212, 3 Aug 16 22:56 frontend0 crw-rw---- 1 root video 212, 7 Aug 16 22:56 net0 and dmesg chunks: bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for captur bttv: Bt8xx card found (0). ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 169 bttv0: Bt878 (rev 17) at 0000:00:0c.0, irq: 169, latency: 32, mmio: 0xea002000 bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00d500ff [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:00:0c.1[A] -> GSI 16 (level, low) -> IRQ 169 bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB functions. bt878(0): Bt878 (rev 17) at 00:0c.1, irq: 169, latency: 32, memory: 0xea003000 dvb_bt8xx: identified card0 as bttv0 DVB: registering new adapter (bttv0). dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 06 00 00 00 00 00 fa ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait ready after 1 dst(0) read_dst: reply is 0x44 0x53 0x54 0x2d 0x30 0x33 0x54 0x31 dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_get_device_id: Recognise [DST-03T] dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 04 00 00 00 00 00 fc ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait ready after 0 dst(0) read_dst: reply is 0x0 0x4 0x0 0x0 0x0 0x0 0x0 0xfc debug_dst_buffer: [ 00 04 00 00 00 00 00 fc] dst(0) dst_get_device_id: Unsupported dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 10 00 00 00 00 00 f0 ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait ready after 0 dst(0) read_dst: reply is 0x13 0x1 0x5 0x3 0x17 0x14 0x54 0x65 debug_dst_buffer: [ 13 01 05 03 17 14 54 65] dst(0) dst_check_mb86a15: Found a MB86A15 NIM dst(0) dst_get_device_id: [DST-03T] has a [MB 86A15] dst(0) dst_get_device_id: [DST-03T] has a [MB 86A15] dst(0) dst_type_print: DST type: satellite DST type flags : 0x2 ts204 0x4 symdiv 0x10 firmware version = 2 dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 0a 00 00 00 00 00 f6 ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait ready after 0 dst(0) read_dst: reply is 0x0 0x8 0xca 0x10 0x19 0xaa 0xf0 0x6b dst(0) dst_get_mac: MAC Address=[00:08:ca:19:aa:00] DVB: registering frontend 0 (DST DVB-S)... dvb_bt8xx: start_feed dvb_bt8xx: start_feed dvb_bt8xx: stop_feed dvb_bt8xx: stop_feed -- Best Regards, Nick Fedchik _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
