Hi,
I am trying to get a DVB card working which has been built into a
Medion/Aldi PC around a year ago, using Kanotix-VDR (Kernel 2.6.16.16).
As this was one of the first solutions that offered DVB-T, DVB-S and
analogue TV on one card, I believe that this is a LifeView clone as this
company was the only one at that time that produced cards with this
capabilities.
This is what I get from lspci:
0000:03:01.0 Multimedia controller: Philips Semiconductors
SAA7134/SAA7135HL Video Broadcast Decoder (rev 01)
Subsystem: Creatix Polymedia GmbH Medion 7134
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 225
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <available only to root>
0000:03:04.0 Multimedia controller: Philips Semiconductors
SAA7134/SAA7135HL Video Broadcast Decoder (rev 01)
Subsystem: Creatix Polymedia GmbH: Unknown device 0005
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 233
Region 0: Memory at d8002000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <available only to root>
Although it says "unknown device 0005" in the second place, I believe to
get success messages with dmesg - at least for the DVB-T part that I need:
...
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 17 (level, low) -> IRQ 225
saa7134[0]: found at 0000:03:01.0, rev: 1, irq: 225, latency: 32, mmio:
0xd8000000
saa7134[0]: subsystem: 16be:0003, board: Medion 7134 [card=12,autodetected]
saa7134[0]: board init: gpio is 400000
ts: Compaq touchscreen protocol output
saa7134[0]: i2c eeprom 00: be 16 03 00 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff 00 01 50 32 79 01 3c ca 50
saa7134[0]: i2c eeprom 20: 01 40 01 02 02 03 01 00 06 ff 00 1f 02 51 96 2b
saa7134[0]: i2c eeprom 30: a7 58 7a 1f 03 8e 84 5e da 7a 04 b3 05 87 b2 3c
saa7134[0]: i2c eeprom 40: ff 1d 00 c2 86 10 01 01 00 00 fd 79 44 9f c2 8f
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff 06 06 0f 00 0f 00 0f 00 0f 00
saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
...
saa7134[0] Board has DVB-T
saa7134[0] Tuner type is 63
...
tuner 1-0061: chip found @ 0xc2 (saa7134[0])
tuner 1-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner)
tda9887 1-0043: chip found @ 0x86 (saa7134[0])
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
saa7134[0]: registered device radio0
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 20 (level, low) -> IRQ 233
saa7134[1]: found at 0000:03:04.0, rev: 1, irq: 233, latency: 32, mmio:
0xd8002000
saa7134[1]: subsystem: 16be:0005, board: UNKNOWN/GENERIC
[card=0,autodetected]
saa7134[1]: board init: gpio is 41002b
saa7134[1]: i2c eeprom 00: be 16 05 00 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[1]: i2c eeprom 10: 00 ff 86 0f ff 20 ff 00 01 50 32 79 01 3c ca 50
saa7134[1]: i2c eeprom 20: 01 40 01 02 02 03 01 00 06 ff 00 21 02 51 96 2b
saa7134[1]: i2c eeprom 30: a7 58 7a 1f 03 8e 84 5e da 7a 04 b3 05 87 b2 3c
saa7134[1]: i2c eeprom 40: ff 24 00 c0 ff 1c 00 ff ff ff fd 79 44 9f c2 8f
saa7134[1]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: registered device video1 [v4l2]
saa7134[1]: registered device vbi1
Unfortunately, VDR finally does not seem to find a working DVB device.
Any hints?
With kind regards
Joerg Knitter
_______________________________________________
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
