I demand that Simon Baxter may or may not have written...
> I'm trying to get some more granluarity on the IR codes produced by my
> remote and WinTV Nova-T card.
[snip]
> Darren's patch [...] I think was written for an A415 remote,
The budget-ci patches assume an R808; the cx88 patch assumes an A415.
> but this patch stops any codes appearing while monitoring 'input-events 2'.
> My remote is a Grey R808-HPG-S 0604 002568.
Hmm... I think that only "R808" is significant. (34-button? Numbers at top?
Colour buttons arranged around the arrow keys?)
> My c programming is very poor. What does the command 'ir->sampling =
> (0x1E<<6) | 1' do?? Is 'ir->sampling' a variable? (can you have '-' &
> '>' in a variable????)
ir is a pointer to a structure. "->" is needed to access the structure
content through the pointer.
> If so, and his A415 remote generates 0x16 to 0x1E (if this is what this
> means), how do I find out what my remote sends?
No. It's (address << 6) | 1; though since the address is 0x1E and not 0, the
"| 1" isn't needed.
> Also, what does 'ir->release = jiffies + msecs_to_jiffies(120)' do?
The calculation is of a timeout, 120ms from the current time.
What you seem to want is this:
# echo 1 >/sys/module/cx88xx/parameters/ir_debug
Now press a key on your remote control - let's say the power button. For my
two remote controls (R808 and A415, in that order):
# dmesg | grep biphase
cx88[0] IR: biphase decoded: 3ffd
cx88[0] IR: biphase decoded: 3fbd
(Don't worry if you see 37fd or 37bd. That's normal; bit 11 is toggled by
the remote control on each new key press. Bits 12 to 15 are fixed; bits 0 to
5 are the key code.)
Plugging the numbers into ((value >> 6) & 0x1F), we get 0x1F and 0x1E.
Once done, don't forget
# echo 0 >/sys/module/cx88xx/parameters/ir_debug
unless you like spamming the kernel message buffer ;-)
If I'm right about this then, for your remote control:
* either:
- replace that 0x1E with 0x1F, so you end up with (0x1F<<6) | 1
- replace the 0x1F which is added in the last hunk of my patch with 0x1E,
which will allow addresses 0x1E and 0x1F; you end up with
((ircode ^ ir->sampling) & (0x1E << 6)))
* recompile, reinstall, reload.
Or you could suffer from interference from the TV remote control:
# echo 1 >/sys/module/cx88xx/parameters/ir_any_address
I'm thinking that maybe we need to add some parameters with suitable
common-case defaults (given here for Nova-T, assuming A415):
ir_address_width (5)
ir_address_shift (6)
ir_address_value (0x1E)
ir_keypress_bit (11)
Except that these should be per-device, not per-module - array, perhaps?
[snip]
--
| Darren Salt | linux or ds at | nr. Ashington, | Toon
| RISC OS, Linux | youmustbejoking,demon,co,uk | Northumberland | Army
| Say NO to UK ID cards. http://www.no2id.net/
It is impossible to make anything foolproof because fools are so ingenious.
_______________________________________________
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
