> If I understand it correctly, this means that the firmware is uploaded, > not everything goes well. I've just made another try. I booted Windows, recorded a show broadcasted in DVB-T, then rebooted linux. This is what I've got after unloading saa7134 card=77, loading saa7134 card=81, modprobing saa7134-dvb and running the scan utility: dmesg output -- [4294771.134000] ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (l evel, low) -> IRQ 17 [4294771.134000] saa7133[0]: found at 0000:05:07.0, rev: 208, irq: 17, latency: 32, mmio: 0xd900a000 [4294771.134000] saa7133[0]: subsystem: 11bd:002f, board: Philips Tiger referenc e design [card=81,insmod option] [4294771.134000] saa7133[0]: board init: gpio is 600e000 [4294771.268000] tuner 0-004b: chip found @ 0x96 (saa7133[0]) [4294771.300000] tuner 0-004b: setting tuner address to 61 [4294771.325000] tuner 0-004b: tuner: type set to tda8290+75a [4294771.361000] saa7133[0]: i2c eeprom read error (err=-5) [4294773.288000] saa7133[0]: registered device video0 [v4l2] [4294773.289000] saa7133[0]: registered device vbi0 [4294773.291000] saa7133[0]: registered device radio0 [4294782.509000] DVB: registering new adapter (saa7133[0]). [4294782.509000] DVB: registering frontend 0 (Philips TDA10046H DVB-T)... [4294812.785000] tda1004x: setting up plls for 48MHz sampling clock [4294812.942000] tda1004x: found firmware revision 29 -- ok [4294812.948000] tda1004x: pll init failed [4294812.964000] tda1004x: pll set failed [4294813.165000] tda1004x: pll set failed [4294813.367000] tda1004x: pll set failed [4294813.569000] tda1004x: pll set failed [4294813.771000] tda1004x: pll set failed [4294813.973000] tda1004x: pll set failed [4294814.176000] tda1004x: pll set failed [4294814.377000] tda1004x: pll set failed [4294814.578000] tda1004x: pll set failed [4294814.780000] tda1004x: pll set failed [4294814.982000] tda1004x: pll set failed [4294815.184000] tda1004x: pll set failed -- scan fails the usual way: -- scanning it-Torino using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 834000000 0 1 0 3 1 3 0 initial transponder 514000000 0 1 0 3 1 3 0 initial transponder 474000000 0 1 0 3 1 3 0 initial transponder 850000000 0 1 0 3 1 3 0 initial transponder 602000000 0 1 0 3 1 3 0 initial transponder 650000000 0 1 0 3 1 3 0 >>> tune to: 834000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_1_2:FEC_NONE:QAM_64:TR ANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE __tune_to_transponder:1290: ERROR: FE_READ_STATUS failed: 5 Input/output error >>> tune to: 834000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_1_2:FEC_NONE:QAM_64:TR ANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE __tune_to_transponder:1290: ERROR: FE_READ_STATUS failed: 5 Input/output error >>> tune to: 514000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_1_2:FEC_NONE:QAM_64:TR ANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE [and so on] -- So I suppose that the with this card the firmware has to be loaded, and it is correctly loaded with Windows. Then it survives the reboot, but the PLL still isn't initialized and set correctly by the tda1004x module. Is there anybody more knowledgeable than me willing to help? What should I try now? Thank you, Pierluigi Rolando _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
