Worked. What changed to get it recognized? Here's my dmesg output: i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100 Linux video capture interface: v1.00 bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11 ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11 bttv0: Bt878 (rev 17) at 0000:01:08.0, irq: 11, latency: 32, mmio: 0xdc000000 bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,insmod option] bttv0: gpio: en=00000000, out=00000000 in=00d500ff [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bttv: Bt8xx card found (1). ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNK3] -> GSI 10 (level, low) -> IRQ 10 bttv1: Bt878 (rev 17) at 0000:01:0a.0, irq: 10, latency: 32, mmio: 0xdc002000 bttv1: detected: AVerMedia TVCapture 98 [card=13], PCI subsystem ID is 1461:0004 bttv1: using: AVerMedia TVCapture 98 [card=13,autodetected] bttv1: gpio: en=00000000, out=00000000 in=00fff7c3 [init] bttv1: Hauppauge/Voodoo msp34xx: reset line init [11] tuner 3-0061: chip found @ 0xc2 (bt878 #1 [sw]) bttv1: Avermedia eeprom[0x4002]: tuner=2 radio:no remote control:no bttv1: using tuner=2 tuner 3-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) bttv1: i2c: checking for MSP34xx @ 0x80... not found bttv1: i2c: checking for MSP34xx (alternate address) @ 0x88... not found bttv1: i2c: checking for TDA9875 @ 0xb0... not found bttv1: i2c: checking for TDA7432 @ 0x8a... not found bttv1: i2c: checking for TDA9887 @ 0x86... not found bttv1: registered device video0 bttv1: registered device vbi0 bttv1: PLL: 28636363 => 35468950 .. ok bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:01:08.1[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11 bt878(0): Bt878 (rev 17) at 01:08.1, irq: 11, latency: 32, memory: 0xdc001000 bt878: Bt878 AUDIO function found (1). ACPI: PCI Interrupt 0000:01:0a.1[A] -> Link [LNK3] -> GSI 10 (level, low) -> IRQ 10 bt878(1): Bt878 (rev 17) at 01:0a.1, irq: 10, latency: 32, memory: 0xdc003000 DVB: registering new adapter (bttv0). dst(0) dst_get_device_id: Recognise [DST-03T] dst(0) dst_get_device_id: Unsupported dst(0) dst_get_device_id: [DST-03T] has a [Fujitsu MB86A15] DST type flags : 0x2 ts204 0x4 symdiv 0x10 firmware version = 2 dst(0) dst_get_mac: MAC Address=[00:08:ca:17:48:00] DVB: registering frontend 0 (DST DVB-S)... it's there: [root@sat ~]# ls /dev/dvb/adapter0/ demux0 dvr0 frontend0 net0 On 2/8/06, Manu Abraham <abraham.manu@xxxxxxxxx> wrote: > Wei Weng wrote: > > Looks exactly like the problem I had been having. (No, I was not able > > to figure it out) > > Please do check whether this helps .. > > http://www.thadathil.net/cgi-bin/hgwebdir.cgi/v4l-algo-test?cmd=archive;node=70266933831bc8efd85ecf808651595f79aede60;type=bz2 > > For build instructions please do refer to the v4l-dvb build > instructions. A simple > make > should build in most cases. Would like to get your feedback on this. > > > Manu > > _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb