Hi, I have a Hauppauge HVR-1100 which was working correctly at early December, 2005 in DVB-T mode. ( The analog audio had problems that time because of the not working cx88-alsa . ) Nowadays I updated the v4l-dvb CVS and I try to use it again and I don't get any data reading from /dev/dvb/adapter0/dvr0. I even tried to use the jelle-cx88-mpeg-restart-queue-fix.patch. I tried to put the card to another PCI slot. Unfortunatelly I don't have the binary drivers used that time. My kernel version is: 2.6.14-gentoo-r5 The dmesg output seems to be OK after modprobe cx88-dvb: -------------------------------------------------------------------------------- Linux video capture interface: v1.00 cx2388x dvb driver version 0.0.5 loaded CORE cx88[0]: subsystem: 0070:9402, board: Hauppauge WinTV-HVR1100 DVB-T/Hybrid [card=40,autodetected] TV tuner 63 at 0x1fe, Radio tuner -1 at 0x1fe tveeprom 0-0050: Hauppauge model 94009, rev C2A0, serial# 119219 tveeprom 0-0050: MAC address is 00-0D-FE-01-D1-B3 tveeprom 0-0050: tuner model is Philips FMD1216ME (idx 100, type 63) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 0-0050: audio processor is CX882 (idx 33) tveeprom 0-0050: decoder processor is CX882 (idx 25) tveeprom 0-0050: has radio, has IR remote cx88[0]: hauppauge eeprom: model=94009 ACPI: PCI Interrupt 0000:00:0e.2[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 cx88[0]/2: found at 0000:00:0e.2, rev: 5, irq: 10, latency: 32, mmio: 0xe1000000cx88[0]/2: cx2388x based dvb card DVB: registering new adapter (cx88[0]). DVB: registering frontend 0 (Conexant CX22702 DVB-T)... -------------------------------------------------------------------------------- The only difference I see compating to the december's log is the 'tveeprom 0-0050: tuner model is Philips FMD1216ME (idx 100, type 63)' line where the tuner type was 4: 'Dec 15 19:11:31 hugo tveeprom 1-0050: tuner model is Philips FMD1216ME (idx 100, type 4) ' The tzap is working correctly with the same settings ( from the dv b-apps cvs ): ./tzap -c channels-conf/dvb-t/hu-Budapest mtv output: -------------------------------------------------------------------------------- hugo szap # ./tzap -c channels-conf/dvb-t/hu-Budapest mtv using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' reading channels from file 'channels-conf/dvb-t/hu-Budapest' tuning to 530000000 Hz video pid 0x0021, audio pid 0x0022 status 00 | signal 005c | snr 8000 | ber 00003fff | unc 00000000 | status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005b | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 005c | snr ffff | ber 00000000 | unc 00000000 | FE_HAS_LOCK -------------------------------------------------------------------------------- The 'cat /dev/dvb/adapter0/dvr0 > /tmp/recording.ts' command result a 0 size file always. The same commands resulted correct mpeg file in early december. After the 'cat' command dmesg shows the following output after and before applying the jelle-cx88-mpeg-restart-queue-fix.patch: -------------------------------------------------------------------------------- cx88[0]/2: queue is empty - first active cx88[0]/2: cx8802_start_dma w: 0, h: 0, f: 2 cx88[0]/2: setting the interrupt mask cx88[0]/2: [da3e1480/0] cx8802_buf_queue - first active cx88[0]/2: queue is empty - first active cx88[0]/2: cx8802_start_dma w: 0, h: 0, f: 2 cx88[0]/2: setting the interrupt mask cx88[0]/2: [d4c64780/0] cx8802_buf_queue - first active -------------------------------------------------------------------------------- Is there anybody who has a working HVR-1100 with the current v4l-dvb CVS ? Does anybody have any idea what could be the problem ? I've read all the video4linux messages and I don't see anybody having the same problem, so maybe something wrong with my setup :-( -- Csaba Paradi csabi@xxxxxxxx Ruby Co. +36 30 9494542
