I'm in the process of setting up a new mythtv system and am having trouble getting ivtv-0.4.1 for my PVR-350 and PVR-500 and dvb kernel module from cvs of yesterday for a DViCO FusionHDTV5 lite to cooperate. I used to have all 3 cards working in an older installation- with older cvs of DVB but doesn't seem to work now. I can get each to work fine on their own, but when dvb is working, the ivtv tuners are not recognized correctly by ivtv: Linux video capture interface: v1.00 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.1 (tagged release) loading ivtv: Linux version: 2.6.14-1.1656_FC4 686 REGPARM 4KSTACKS gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 350 card (cx23415 based) ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11 ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] tveeprom 2-0050: Hauppauge model 48132, rev K168, serial# 7520207 tveeprom 2-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is MSP4448 (idx 27) tveeprom 2-0050: decoder processor is SAA7115 (idx 19) tveeprom 2-0050: has radio, has IR remote tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] saa7127 2-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44] msp3400 2-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0) msp3400 2-0040: MSP4448G-A2 supports radio, mode is autodetect and autoselect ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40] tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02040024 ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv0: Decoder revision: 0x02020023 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) ivtv0: Create decoder VOUT stream ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total) ivtv0: unable to open firmware v4l-cx2341x-init-mpeg.bin ivtv0: did you put the firmware in the hotplug firmware directory? ivtv0: failed to read mpeg decoder initialisation file v4l-cx2341x-init-mpeg.bin tuner 2-0061: tuner type not set tuner 2-0061: tuner type not set spurious 8259A interrupt: IRQ7. ivtv0: Initialized WinTV PVR 350, card #0 ivtv: ====================== NEXT CARD ====================== ivtv1: Autodetected WinTV PVR 150 card (cx23416 based) ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNK4] -> GSI 9 (level, low) -> IRQ 9 ivtv1: Unreasonably low latency timer, setting to 64 (was 32) ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50] tuner 3-0060: TEA5767 detected. tuner 3-0060: chip found @ 0xc0 (ivtv i2c driver #1) ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=60] tuner 3-0060: type set to 62 (Philips TEA5767HN FM Radio) tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1) ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61] tda9887 3-0043: chip found @ 0x86 (ivtv i2c driver #1) ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43] tveeprom 3-0050: Hauppauge model 23552, rev D492, serial# 7855692 tveeprom 3-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57) tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 3-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62) tveeprom 3-0050: audio processor is CX25843 (idx 37) tveeprom 3-0050: decoder processor is CX25843 (idx 30) tveeprom 3-0050: has radio, has no IR remote ivtv1: This is the first unit of a PVR500 cx25840 3-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1) cx25840 3-0044: loaded v4l-cx25840.fw firmware (13353 bytes) ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44] wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1) ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b] ivtv1: Detected a TEA5767 radio tuner. Enabling radio support. ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv1: Encoder revision: 0x02040024 ivtv1 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv1: Create encoder radio stream cx25840 3-0044: 0x0000 is not a valid video input! tuner 3-0061: tuner type not set tuner 3-0061: tuner type not set ivtv1: Initialized WinTV PVR 500 (unit #1), card #1 ivtv: ====================== NEXT CARD ====================== ivtv2: Autodetected WinTV PVR 150 card (cx23416 based) ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11 ivtv2: Unreasonably low latency timer, setting to 64 (was 32) ivtv2: i2c attach to card #2 ok [client=tveeprom, addr=50] tuner 4-0061: chip found @ 0xc2 (ivtv i2c driver #2) ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=61] tda9887 4-0043: chip found @ 0x86 (ivtv i2c driver #2) ivtv2: i2c attach to card #2 ok [client=tda9887, addr=43] cx25840 4-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #2) cx25840 4-0044: loaded v4l-cx25840.fw firmware (13353 bytes) ivtv2: i2c attach to card #2 ok [client=cx25840, addr=44] wm8775 4-001b: chip found @ 0x36 (ivtv i2c driver #2) ivtv2: i2c attach to card #2 ok [client=wm8775, addr=1b] tveeprom 4-0050: Hauppauge model 23552, rev D492, serial# 7855692 tveeprom 4-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57) tveeprom 4-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 4-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62) tveeprom 4-0050: audio processor is CX25843 (idx 37) tveeprom 4-0050: decoder processor is CX25843 (idx 30) tveeprom 4-0050: has radio, has no IR remote ivtv2: This is the second unit of a PVR500 ivtv2: Correcting tveeprom data: no radio present on second unit ivtv2: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv2: Encoder revision: 0x02040024 ivtv2 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv2: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv2: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv2: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) cx25840 4-0044: 0x0000 is not a valid video input! tuner 4-0061: tuner type not set tuner 4-0061: tuner type not set ivtv2: Initialized WinTV PVR 500 (unit #2), card #2 ivtv: ==================== END INIT IVTV ==================== bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNK2] -> GSI 5 (level, low) -> IRQ 5 bttv0: Bt878 (rev 17) at 0000:01:07.0, irq: 5, latency: 32, mmio: 0xe4000000 bttv0: detected: DViCO FusionHDTV 5 Lite [card=135], PCI subsystem ID is 18ac:d500 bttv0: using: DViCO FusionHDTV 5 Lite [card=135,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init] tuner 5-0061: chip found @ 0xc2 (bt878 #0 [sw]) tda9887 5-0043: chip found @ 0x86 (bt878 #0 [sw]) bttv0: using tuner=64 tuner 5-0061: type set to 64 (LG TDVS-H062F/TUA6034) bttv0: registered device video3 bttv0: registered device vbi3 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:01:07.1[A] -> Link [LNK2] -> GSI 5 (level, low) -> IRQ 5 bt878(0): Bt878 (rev 17) at 01:07.1, irq: 5, latency: 32, memory: 0xe4001000 DVB: registering new adapter (bttv0). DVB: registering frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)... If I then re-install the ivtv-driver, the PVR-*** are working, but the DVB is broken... ivtv: no version for "struct_module" found: kernel tainted. ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.1 (tagged release) loading ivtv: Linux version: 2.6.14-1.1656_FC4 686 REGPARM 4KSTACKS gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 350 card (cx23415 based) ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11 ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: ivtv version tveeprom: Hauppauge: model = 48132, rev = K168, serial# = 7520207 tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = MSP4448 (type = 1b) tveeprom: decoder processor = SAA7115 (type = 13) ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] saa7115 2-0021: ivtv driver saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] saa7127 2-0044: ivtv driver saa7127 2-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44] msp3400 2-0040: ivtv driver msp3400 2-0040: chip=MSP4448G-A2 +nicam +simple +simpler +radio mode=simpler ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40] msp3400 2-0040: msp34xxg daemon started tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02040024 ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv0: Decoder revision: 0x02020023 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) ivtv0: Create decoder VOUT stream ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total) ivtv0: loaded v4l-cx2341x-init-mpeg.bin firmware (155648 bytes) tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0 ivtv0: Initialized WinTV PVR 350, card #0 ivtv: ====================== NEXT CARD ====================== ivtv1: Autodetected WinTV PVR 150 card (cx23416 based) ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNK4] -> GSI 9 (level, low) -> IRQ 9 ivtv1: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: Second (radio) tuner idx 101 tveeprom: ivtv version tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7855692 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50] tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv i2c driver #1 TEA5767 detected. ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=60] tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect type set to 62 (Philips TEA5767HN FM Radio) tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61] tda9887 3-0043: chip found @ 0x86 (ivtv i2c driver #1) ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43] ivtv1: This is the first unit of a PVR500 cx25840 3-0044: ivtv driver cx25840 3-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1) spurious 8259A interrupt: IRQ7. cx25840 3-0044: loaded v4l-cx25840.fw firmware (13353 bytes) ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44] wm8775 3-001b: ivtv driver wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1) ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b] ivtv1: Detected a TEA5767 radio tuner. Enabling radio support. ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv1: Encoder revision: 0x02040024 ivtv1 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv1: Create encoder radio stream tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv1: Initialized WinTV PVR 500 (unit #1), card #1 ivtv: ====================== NEXT CARD ====================== ivtv2: Autodetected WinTV PVR 150 card (cx23416 based) ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11 ivtv2: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: Second (radio) tuner idx 101 tveeprom: ivtv version tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7855692 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv2: i2c attach to card #2 ok [client=tveeprom, addr=50] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #2 ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=61] tda9887 4-0043: chip found @ 0x86 (ivtv i2c driver #2) ivtv2: i2c attach to card #2 ok [client=tda9887, addr=43] cx25840 4-0044: ivtv driver cx25840 4-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #2) cx25840 4-0044: loaded v4l-cx25840.fw firmware (13353 bytes) ivtv2: i2c attach to card #2 ok [client=cx25840, addr=44] wm8775 4-001b: ivtv driver wm8775 4-001b: chip found @ 0x36 (ivtv i2c driver #2) ivtv2: i2c attach to card #2 ok [client=wm8775, addr=1b] ivtv2: This is the second unit of a PVR500 ivtv2: Correcting tveeprom data: no radio present on second unit ivtv2: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv2: Encoder revision: 0x02040024 ivtv2 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv2: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv2: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv2: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #2 ivtv2: Initialized WinTV PVR 500 (unit #2), card #2 ivtv: ==================== END INIT IVTV ==================== bttv: disagrees about version of symbol tveeprom_hauppauge_analog bttv: Unknown symbol tveeprom_hauppauge_analog bt878: Unknown symbol bttv_read_gpio bt878: Unknown symbol bttv_write_gpio bt878: Unknown symbol bttv_gpio_enable bttv: disagrees about version of symbol tveeprom_hauppauge_analog bttv: Unknown symbol tveeprom_hauppauge_analog This is a fresh install of FC4, following Jarod's howto... It doesn't matter whether I install ivtv from the rpm using yum or manually. I've googled a bit on this topic, but am not finding anything. I'm pretty sure it's all due to the rapid development of these two drivers and will sort itself out eventually, but if I can help that process, please let me know. If I've missed something please feel free to point me in the correct direction. thanks, Mike -------------- next part -------------- An HTML attachment was scrubbed... URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20060111/7ee5000b/attachment-0001.htm
