Hi, You need to supply the -r option to czap to set up /dev/dvb/adapterX/dvr0 for TS recording. This seems not to be documented for czap (czap -h) but is for tzap and szap (se szap -h). However, the option seems to be present in the source code for czap. So something like: peterr-alfa2 ~ # czap -r "RTL 5" and then in another window (while still running czap in the first): peterr-alfa2 ~ # cat /dev/dvb/adapter0/dvr0 > /data/test.ts Hope this helps. Regards, Henrik > I have already going through: > http://www.linuxtv.org/pipermail/linux-dvb/2005-September/004871.html > > The card can tune and scan. But no picture. > I have try: > > peterr-alfa2 ~ # czap "RTL 5" > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > reading channels from file '/root/.czap/channels.conf' > 4 RTL 5:340000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64:1910:1911:2009 > 4 RTL 5: f 340000000, s 6875000, i 2, fec 0, qam 3, v 0x776, a 0x777 > status 00 | signal 0000 | snr 0000 | ber 6e65672d | unc 34312e36 | > status 1f | signal 0000 | snr 3200 | ber 6e65672d | unc 34312e36 | > FE_HAS_LOCK > status 1f | signal 0000 | snr 3200 | ber 6e65672d | unc 34312e36 | > FE_HAS_LOCK > > And: > > peterr-alfa2 ~ # cat /dev/dvb/adapter0/dvr0 > /data/test.ts > The test.ts is 0 bytes and wont play. > > And: > > Mplayer dvb://"RTL 5" > Mplayer crashed because it can't read the stream. > > If I start the czap command this will written in the dmesg (a peace of > it): > > rdc_reset_state: Resetting state machine > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] > writing [ 09 00 05 30 20 00 1a db 40 6d ] > dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] > read_dst: reply is 0xff > dst_wait_dst_ready: dst wait ready after 2 > read_dst: reply is 0x9 > 0x0 0x5 0x30 0x20 0x0 0x1a 0xdb 0x40 0x6d > dst_comm_init: Initializing DST. > dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] > rdc_reset_state: Resetting state machine > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] > writing [ 00 05 00 00 00 00 00 fb ] > dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] > read_dst: reply is 0xff > dst_wait_dst_ready: dst wait ready after 2 > read_dst: reply is 0x0 > 0x5 0x0 0x32 0x0 0x5c 0x0 0x6d > dst_comm_init: Initializing DST. > dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] > rdc_reset_state: Resetting state machine > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] > writing [ 00 05 00 00 00 00 00 fb ] > dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] > read_dst: reply is 0xff > dst_wait_dst_ready: dst wait ready after 2 > read_dst: reply is 0x0 > 0x5 0x0 0x32 0x0 0x5c 0x0 0x6d > dst_comm_init: Initializing DST. > dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] > rdc_reset_state: Resetting state machine > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] > dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] > writing [ 00 05 00 00 00 00 00 fb ] > dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] > read_dst: reply is 0xff > dst_wait_dst_ready: dst wait ready after 2 > read_dst: reply is 0x0 > 0x5 0x0 0x32 0x0 0x5c 0x0 0x6d > > > There is one thing I didn't try, because I can't find: >> try changing the dst_tlist[] (for DCT-CI ) >> .type_flags = DST_TYPE_HAS_NEWTUNE | DST_TYPE_HAS_FW_2 >> only and see what happens. > > I using kernel 2.6.14 r5 (gentoo) > > Thanks for any help. > > Jovana > > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >
