Hi, I have some trouble with my Pinnacle 300i again. After I have updated my kernel from 2.6.12 to 2.6.14 I can not tune any channel anymore. I installed the latest CVS v4l-dvb drivers into my kernel. After I've executeted "modprobe saa7134-dvb" I can find the following output in my /var/log/messages: Dec 15 21:46:46 Linux video capture interface: v1.00 Dec 15 21:46:46 saa7130/34: v4l2 driver version 0.2.14 loaded Dec 15 21:46:46 ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 17 Dec 15 21:46:46 saa7134[0]: found at 0000:00:0a.0, rev: 1, irq: 17, latency: 32, mmio: 0xcfffcc00 Dec 15 21:46:46 saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected] Dec 15 21:46:46 saa7134[0]: board init: gpio is 8806000 Dec 15 21:46:46 saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92 Dec 15 21:46:46 saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff Dec 15 21:46:46 saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff Dec 15 21:46:46 saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Dec 15 21:46:46 saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff Dec 15 21:46:46 saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Dec 15 21:46:46 saa7134[0]: i2c eeprom 60: 0c 22 17 44 02 9f 6a 13 ff ff ff ff ff ff ff ff Dec 15 21:46:46 saa7134[0]: i2c eeprom 70: 00 30 8d 15 b4 f4 ff ff 74 9c ff ff ff ff ff ff Dec 15 21:46:46 tda9887 0-0043: chip found @ 0x86 (saa7134[0]) Dec 15 21:46:46 saa7134[0]: registered device video0 [v4l2] Dec 15 21:46:46 saa7134[0]: registered device vbi0 Dec 15 21:46:47 saa7134[0]: pinnacle 300i dvb setup Dec 15 21:46:47 DVB: registering new adapter (saa7134[0]). Dec 15 21:46:47 DVB: registering frontend 0 (Zarlink MT352 DVB-T)... So, it looks again like no errors are reported and the card as well as the frontend can be detected by the driver. But if i try to tune a channel via tzap I only get the following message in my /var/log/messages: Dec 15 21:51:04 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:04 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:05 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:06 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:07 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:08 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:09 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:10 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:11 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:12 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:13 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:14 saa7134[0]: mt352_pinnacle_init called Dec 15 21:51:16 saa7134[0]: mt352_pinnacle_init called And as tzap shows no channel could be locked: status 00 | signal 1ebf | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 1fbf | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 1f3f | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 1f5f | snr 0000 | ber 00000000 | unc 00000000 | status 04 | signal 1edf | snr 0000 | ber 00000000 | unc 00000000 | status 04 | signal 1e1f | snr 0000 | ber 00000000 | unc 00000000 | Can someone help me? Tim
