Le Samedi 12 Novembre 2005 20:43, Thomas Gutzler a ?crit?: > Hi, > > I am trying to get my dvb card running but i just doesn't work and I am > running out of ideas. I'm using gentoo and tried the current kernel > which is 2.6.13-gentoo-r5 and also 2.6.11 with patches. > The latest attempt was to get 2.6.14.2 kernel sources, apply the > v4l-kernel and dvb-kernel CVS sources and build everything like it's > described in http://linuxtv.org/v4lwiki/index.php/How_to_build_from_CVS. > > I am sure that the card has a Thomson 7579 tuner rather than a Philips. > It's written on the can: DTT 7579 > This is an Australian card and we're using PAL over here. > > This is what happens: > # modprobe bttv > bttv: driver version 0.9.16 loaded > bttv: using 8 buffers with 2080k (520 pages) each for capture > bttv: Bt8xx card found (0). > ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> > IRQ 5 bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 5, latency: 32, mmio: > 0xdf002000 bttv0: detected: DViCO FusionHDTV DVB-T Lite [card=128], PCI > subsystem ID is 18ac:db10 bttv0: using: DViCO FusionHDTV DVB-T Lite > [card=128,autodetected] > bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init] > bttv0: using tuner=-1 > bttv0: add subdevice "dvb0" > # modprobe dvb-bt8xx > bt878: AUDIO driver version 0.0.0 loaded > bt878: Bt878 AUDIO function found (0). > ACPI: PCI Interrupt 0000:00:09.1[A] -> Link [LNKB] -> GSI 5 (level, low) > -> IRQ 5 > bt878(0): Bt878 (rev 17) at 00:09.1, irq: 5, latency: 32, memory: > 0xdf000000 > DVB: registering new adapter (bttv0). > DVB: registering frontend 0 (Zarlink MT352 DVB-T)... > > I tried modprobe bttv tuner=42 but the result is the same: > linuxtv-dvb-apps-1.1.0/util/szap/tzap "Digital" > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > tuning to 177500000 Hz > video pid 0x0601, audio pid 0x0602 > status 00 | signal 90ef | snr 0000 | ber 00000000 | unc 00000000 | > status 1f | signal a6bf | snr bfbf | ber 00000000 | unc 00000000 | > FE_HAS_LOCK status 1f | signal a6bf | snr c2c2 | ber 00000000 | unc > 00000000 | FE_HAS_LOCK and so on.. > > but cat /dev/dvb/adapter0/dvr0 is just empty give tzap the option "-r" > Any Ideas how to get that thing running? > Here are some more outputs: > # lspci -v > 0000:00:09.0 Multimedia video controller: Brooktree Corporation Bt878 > Video Capture (rev 11) > Subsystem: DViCO Corporation: Unknown device db10 > Flags: bus master, medium devsel, latency 32, IRQ 5 > Memory at df002000 (32-bit, prefetchable) [size=4K] > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > > 0000:00:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio > Capture (rev 11) > Subsystem: DViCO Corporation: Unknown device db10 > Flags: bus master, medium devsel, latency 32, IRQ 5 > Memory at df000000 (32-bit, prefetchable) [size=4K] > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > > # lsmod > Module Size Used by > dvb_bt8xx 12292 0 > nxt6000 7172 1 dvb_bt8xx > mt352 5892 1 dvb_bt8xx > dvb_pll 8708 1 dvb_bt8xx > sp887x 7492 1 dvb_bt8xx > dst_ca 15808 1 dvb_bt8xx > dst 24964 2 dvb_bt8xx,dst_ca > bt878 8120 2 dvb_bt8xx,dst > dvb_core 75944 2 dvb_bt8xx,dst_ca > cx24110 7812 1 dvb_bt8xx > or51211 9348 1 dvb_bt8xx > lgdt330x 7388 1 dvb_bt8xx > bttv 156496 2 dvb_bt8xx,bt878 > video_buf 17284 1 bttv > compat_ioctl32 896 1 bttv > i2c_algo_bit 8776 1 bttv > v4l2_common 4544 1 bttv > btcx_risc 3784 1 bttv > tveeprom 12816 1 bttv > videodev 7232 1 bttv > tuner 43300 0 > i2c_core 17744 12 > dvb_bt8xx,nxt6000,mt352,sp887x,dst,cx24110,or51211,lgdt330x,bttv,i2c_algo_b >it,tveeprom,tuner > > Cheers, > Tom -- Christophe Thommeret
