Hello, I bought this card and don't got it work. I tried out dvb-modules of the newest Kernel 2.6.14RC4. After 'modprobe saa7134_dvb' I get: saa7130/34: v4l2 driver version 0.2.14 loaded PCI: Found IRQ 11 for device 0000:00:0a.0 saa7134[0]: found at 0000:00:0a.0, rev: 1, irq: 11, latency: 32, mmio: 0xeb020000 saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected] saa7134[0]: board init: gpio is c806000 saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92 saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: registered device video1 [v4l2] saa7134[0]: registered device vbi0 saa7134[0]: pinnacle 300i dvb setup DVB: registering new adapter (saa7134[0]). DVB: registering frontend 1 (Zarlink MT352 DVB-T)... This modules are new loaded: Module Size Used by saa7134_dvb 8292 0 mt352 6756 1 saa7134_dvb saa7134 116532 1 saa7134_dvb ir_common 8836 1 saa7134 video_buf_dvb 6468 1 saa7134_dvb This are already loaded modules video_buf 22148 4 saa7134_dvb,saa7134,video_buf_dvb,saa7146_vv v4l1_compat 14404 2 saa7134,saa7146_vv v4l2_common 5664 2 saa7134,saa7146_vv videodev 9376 2 saa7134,saa7146_vv tda1004x 16004 2 saa7134_dvb,budget_ci i2c_core 22384 15 saa7134_dvb,mt352,saa7134,dvb_ttpci,l64781,ves1820,tda8083,sp8870,ves1x93,budget_ci,tda1004x,budget_core,ttpci_eeprom,stv0299,stv0297 soundcore 9920 2 saa7134,snd I can also modprobe tda9887 then I got this kernel message: tda9885/6/7: chip found @ 0x86 But it isn't used by anything: lsmod Module Size Used by tda9887 13808 0 I'm missing this kernel outputs described at http://de.gentoo-wiki.com/Pinnacle_300i tuner 0-0060: chip found @ 0xc0 (saa7134[0]) tuner 0-0060: microtune: companycode=3cbf part=42 rev=2f tuner 0-0060: microtune MT2050 found, OK Maybe I forgot a modul? The problem is, that I can't tune to any channel: `--> tzap -a1 "RTL" using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0' tuning to 538000000 Hz video pid 0x01b1, audio pid 0x01b2 status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 | .. .. With a technotrend card and the same antenna it work's fine with strong signal. When I trie to tune with tzap, the kernel says: saa7134[0]: mt352_pinnacle_init called saa7134[0]: mt352_pinnacle_init called saa7134[0]: mt352_pinnacle_init called saa7134[0]: mt352_pinnacle_init called saa7134[0]: mt352_pinnacle_init called saa7134[0]: mt352_pinnacle_init called .. .. Anyone have an idea or HOWTO to get this card working? Thanks in advance and excuse my bas english, Dominik (from germany) PS: I read about a v4l2 version problem on this list on earlier kernel versions. Maybe it is still not solved in the newest kernel?
