Hi,
I have still problems to get my Pinnacle 300i running with gentoo (kernel
2.6.12-gentoo-r6).
I don't know if i installed all the needed modules. "lsmod" shows me the
following lines:
[BEGIN lsmod]
Module Size Used by
budget_ci 11776 0
budget_core 7748 1 budget_ci
or51132 10308 0
i2c_sensor 3968 0
saa7134_empress 7428 0
cx22702 6148 0
i2c_sis96x 5828 0
dvb_ttpci 93552 0
saa7146_vv 46272 1 dvb_ttpci
stv0299 11080 2 budget_ci,dvb_ttpci
ves1x93 6788 1 dvb_ttpci
ttpci_eeprom 2688 2 budget_core,dvb_ttpci
saa7134_dvb 4932 0
saa7134 102996 2 saa7134_empress,saa7134_dvb
video_buf_dvb 5124 1 saa7134_dvb
bt878 8792 0
bttv 150352 1 bt878
btcx_risc 4360 1 bttv
tuner 26920 0
mt352 6532 1 saa7134_dvb
tda9887 13144 0
tda1004x 14724 2 budget_ci,saa7134_dvb
tveeprom 12120 1 bttv
dvb_pll 4228 2 or51132,cx22702
i2c_algo_bit 9544 1 bttv
dvb_core 77544 4
budget_ci,budget_core,dvb_ttpci,video_buf_dvb
l64781 7492 1 dvb_ttpci
video_buf 17924 6
saa7134_empress,saa7146_vv,saa7134_dvb,saa7134,video_buf_dvb,bttv
saa7146 15368 4 budget_ci,budget_core,dvb_ttpci,saa7146_vv
v4l1_compat 14084 2 saa7146_vv,saa7134
v4l2_common 5184 3 saa7146_vv,saa7134,bttv
videodev 7808 4 saa7134_empress,saa7146_vv,saa7134,bttv
ves1820 5892 1 dvb_ttpci
tda8083 6148 1 dvb_ttpci
stv0297 9024 1 dvb_ttpci
sp8870 7564 1 dvb_ttpci
firmware_class 8448 6
budget_ci,or51132,dvb_ttpci,saa7134_dvb,bttv,sp8870
pci_hotplug 11332 0
ir_common 6660 1 saa7134
snd_intel8x0 29440 2
snd_ac97_codec 79032 1 snd_intel8x0
[END lsmod]
While the system activates the saa7134_dvb and saa7134 module, tail -f
/var/log/messages shows the following output:
[BEGIN tail -f /var/log/messages]
saa7130/34: v4l2 driver version 0.2.12 loaded
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 17
saa7134[0]: found at 0000:00:09.0, rev: 1, irq: 17, latency: 32,
mmio: 0xcfffbc00
saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T
+ PAL [card=50,autodetected]
saa7134[0]: board init: gpio is c806000
i2c_adapter i2c-0: Registered as minor 0
i2c_adapter i2c-0: found normal i2c entry for adapter 0, addr 42
i2c_adapter i2c-0: master_xfer[0] W, addr=0x42, len=0
i2c_adapter i2c-0: found normal i2c entry for adapter 0, addr 43
i2c_adapter i2c-0: master_xfer[0] W, addr=0x43, len=0
tda9885/6/7: chip found @ 0x86
i2c_adapter i2c-0: master_send: writing 4 bytes.
i2c_adapter i2c-0: client [tda9887] registered to adapter
registering 0-0043
i2c_adapter i2c-0: found normal i2c entry for adapter 0, addr 4b
i2c_adapter i2c-0: master_xfer[0] W, addr=0x4b, len=0
i2c_adapter i2c-0: found normal i2c entry for adapter 0, addr 4b
i2c_adapter i2c-0: master_xfer[0] W, addr=0x4b, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0060
i2c_adapter i2c-0: master_xfer[0] W, addr=0x60, len=0
i2c_adapter i2c-0: master_send: writing 4 bytes.
i2c_adapter i2c-0: client [(tuner unset)] registered to adapter
registering 0-0060
tuner 0-0060: chip found @ 0xc0 (saa7134[0])
i2c_adapter i2c-0: master_send: writing 1 bytes.
i2c_adapter i2c-0: master_recv: reading 21 bytes.
i2c_adapter i2c-0: master_recv: return:1 (count:21, addr:0x60)
tuner 0-0060: microtune: companycode=3cbf part=42 rev=83
i2c_adapter i2c-0: master_send: writing 2 bytes.
i2c_adapter i2c-0: master_send: writing 2 bytes.
i2c_adapter i2c-0: master_send: writing 1 bytes.
i2c_adapter i2c-0: master_recv: reading 1 bytes.
i2c_adapter i2c-0: master_recv: return:1 (count:1, addr:0x60)
tuner 0-0060: microtune MT2050 found, OK
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0061
i2c_adapter i2c-0: master_xfer[0] W, addr=0x61, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0062
i2c_adapter i2c-0: master_xfer[0] W, addr=0x62, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0063
i2c_adapter i2c-0: master_xfer[0] W, addr=0x63, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0064
i2c_adapter i2c-0: master_xfer[0] W, addr=0x64, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0065
i2c_adapter i2c-0: master_xfer[0] W, addr=0x65, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0066
i2c_adapter i2c-0: master_xfer[0] W, addr=0x66, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0067
i2c_adapter i2c-0: master_xfer[0] W, addr=0x67, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0068
i2c_adapter i2c-0: master_xfer[0] W, addr=0x68, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
0069
i2c_adapter i2c-0: master_xfer[0] W, addr=0x69, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
006a
i2c_adapter i2c-0: master_xfer[0] W, addr=0x6a, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
006b
i2c_adapter i2c-0: master_xfer[0] W, addr=0x6b, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
006c
i2c_adapter i2c-0: master_xfer[0] W, addr=0x6c, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
006d
i2c_adapter i2c-0: master_xfer[0] W, addr=0x6d, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
006e
i2c_adapter i2c-0: master_xfer[0] W, addr=0x6e, len=0
i2c_adapter i2c-0: found normal i2c_range entry for adapter 0, addr
006f
i2c_adapter i2c-0: master_xfer[0] W, addr=0x6f, len=0
i2c_adapter i2c-0: registered as adapter #0
i2c_adapter i2c-0: master_send: writing 1 bytes.
i2c_adapter i2c-0: master_recv: reading 64 bytes.
i2c_adapter i2c-0: master_recv: return:1 (count:64, addr:0x50)
saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55
d2 b2 92
saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff
ff ff ff
saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff
ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff
i2c_adapter i2c-0: master_send: writing 4 bytes.
i2c_adapter i2c-0: master_send: writing 4 bytes.
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
saa7134[0]: pinnacle 300i dvb setup
i2c_adapter i2c-0: master_xfer[0] W, addr=0x1e, len=1
i2c_adapter i2c-0: master_xfer[1] R, addr=0x1e, len=1
DVB: registering new adapter (saa7134[0]).
saa7134[0]/audio: audio carrier scan failed, using 5.500 MHz
[default]
[END tail -f /var/log/messages]
Although hwinfo --dvb does not show anything, it is possible to start VDR.
The nodes in /dev/dvb/adapter0/ are available, but I am not able to
recieve anything.
Yesterday, as I started the my system with an aditional analog TV-card
pluged in,
hwinfo --dvb showed me the Pinnacle 300i as a dvb card and even kaffeine
found
it as a dvb-device, but I also wasn't able to see anything and no channel
were found
while scanning. When I selected a channel manualy, kaffeine crashed.
Regards,
Tim
