Hello Manu, Sorry for sending this mail again, because I forgot add your address in the first mail... I've struggled with my new TWINHAN MINICAB DVB-C card (vp-2021) for weeks, but failed. I tested it under M$ windows XP and succeeded. When I tested it on kernel 2.6.12, all the relative modules (bttv, dst, dst_ca, dvb_bt8xx etc.) were loaded without error. But when I used scan to tune channels, scan always feed me with "tuning failed". I opened the debug switch for each modules(set 5 for all) and I didn't see any obvious bad message from dmesg. I've update kernel 2.6.12 with newest patch (12 Jul ,linuxtv.org/download), it didn't help too. Also I went through divers source of DVB/bt8xx/, and found that the driver recognized my card as DCT-CI with CA features. But I'm very sure that this card doesn't have any relation to CA, it's only a pity mini one. So I tried to replace code of DCT-CI section with code of DCTNEW section in "dst_types dst_tlist[]" in "dst.c", but it didn't change anything. Below is related info on core 2.6.12: CARD LOADING INFO: ----------------------------------------------------------------------------------------- Linux video capture interface: v1.00 bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 17 (level, low) -> IRQ 193 bttv0: Bt878 (rev 17) at 0000:02:06.0, irq: 193, latency: 64, mmio: 0xfc200000 bttv0: using: Twinhan DST + clones [card=113,insmod option] bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:02:06.1[A] -> GSI 17 (level, low) -> IRQ 193 bt878(0): Bt878 (rev 17) at 02:06.1, irq: 193, latency: 64, memory: 0xfc201000 dvb_bt8xx: identified card0 as bttv0 DVB: registering new adapter (bttv0). rdc_8820_reset: Resetting DST dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst_comm_init: Initializing DST.. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] write_dst writing 00 06 00 00 00 00 00 fa dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst reply is 0xff dst_wait_dst_ready: dst wait ready after 0 read_dst reply is 0x0 0x44 0x43 0x54 0x2d 0x43 0x49 0x6c dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst_get_device_id: Recognise [DCT-CI] DST type : cable DST type flags : 0x1 newtuner 0x2 ts204 0x8 firmware version = 1 0x10 firmware version = 2 DVB: registering frontend 0 (DST DVB-C)... ------------------------------------------------------------------------------------- +++++++++++++++++++++++++++++++++++++++++++++++++++++ SCAN message ------------------------------------------------------------------------------------- FROM scan: using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 738000000 6900000 0 3 >>>tune to: 738000000:INVERSION_AUTO:6900000:FEC_NONE:QAM_64 WARNING: >>> tuning failed!!! >>>tune to: 738000000:INVERSION_AUTO:6900000:FEC_NONE:QAM_64 (tuning failed) WARNING: >>> tuning failed!!! ERROR: initial tuning failed dumping lists (0 services) Done. FROM dmesg(repeated hundreds times, full of the screen:): dst_set_freq: set Frequency 738000000 Set Frequency = [738000000] dst_set_symbolrate: set symrate 6900000 dst_write_tuna: type_flags 0x5b dst_comm_init: Initializing DST.. dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] rdc_reset_state: Resetting state machine dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] write_dst writing 09 00 0b 42 d0 00 1a f4 80 4c dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] read_dst reply is 0xff dst_wait_dst_ready: dst wait ready after 116 read_dst reply is 0x9 0x0 0x0 0x0 0x50 0x4b 0x4b 0x96 0x8 0x73 -------------------------------------------------------------------------------------- I checked google and linux-dvb maillist, it seemed someone had made the same card working with CVS code at the end of year 2004 and another said everything was ok before TWINHAN_xxx branch of bt8xx, so I got all kernels of 2.6.11.x and 2.6.12.x and tried them, then also try to downgrade DVB driver to late 2004 CVS stuff, but still failed. I also noticed that there is a LED on the card, when in 2.6.12, the LED twinkled during tuning against no response in 2.6.11.12. I am totally frustrated now, really need your help. BTW, as a newbie, I have succeeded in running a TechnoTrend full card on my friends' machine, it works great! Many thanks to all linuxdvb devels. Jeff _________________________________________________________________ Express yourself instantly with MSN Messenger! Download today it's FREE! http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
