Nico Sabbi wrote: > > try to remove card=39 > hi, i'd like to share some more info about the test i'm doing following nico suggestion, i tried to load the card this way: #modprobe saa7134 tuner=54 i2c_scan=1 this is the relevant "dmesg" entry: ========================================= Linux video capture interface: v1.00 saa7130/34: v4l2 driver version 0.2.12 loaded saa7130/34: snapshot date 2005-03-10 PCI: Enabling device 0000:04:00.0 (0000 -> 0002) ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 217 saa7133[0]: found at 0000:04:00.0, rev: 240, irq: 217, latency: 0, mmio: 0x40800000 PCI: Setting latency timer of device 0000:04:00.0 to 64 saa7133[0]: subsystem: 5168:0502, board: UNKNOWN/GENERIC [card=0,autodetected] saa7133[0]: board init: gpio is e010000 saa7133[0]: dsp access wait timeout [bit=WRR] saa7133[0]: dsp access wait timeout [bit=WRR] saa7133[0]: i2c eeprom 00: 68 51 02 05 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: 00 ff 22 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 aa ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c scan: found device @ 0x10 [???] saa7133[0]: i2c scan: found device @ 0x96 [???] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] tuner 1-004b: chip found @ 0x96 (saa7133[0]) tuner 1-004b: tuner: type set to tda8290+75 saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 ========================================= this way, YES, i can receive analog TV! but tvtime can't see anymore the composite and svideo input capabilities! anyway, using this modprobe line: #modprobe saa7134 card=39 i2c_scan=1 these are the dmesg entries ======================================== saa7130/34: v4l2 driver version 0.2.12 loaded saa7130/34: snapshot date 2005-03-10 ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 217 saa7133[0]: found at 0000:04:00.0, rev: 240, irq: 217, latency: 64, mmio: 0x40800000 saa7133[0]: subsystem: 5168:0502, board: LifeView FlyTV Platinum Mini [card=39,insmod option] saa7133[0]: board init: gpio is e010000 saa7133[0]: dsp access wait timeout [bit=WRR] saa7133[0]: dsp access wait timeout [bit=WRR] tuner 1-004b: chip found @ 0x96 (saa7133[0]) tuner 1-004b: tuner: type set to tda8290+75 saa7133[0]: i2c eeprom 00: 68 51 02 05 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: 00 ff 22 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 aa ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c scan: found device @ 0x10 [???] saa7133[0]: i2c scan: found device @ 0x96 [???] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 ======================================== status: - i still can see the analog tv - tvtime can find the svideo and composite1 inputs but, - i don't see a known good composite source thru the composite input so for the svideo & composite input support, it should be "still" just a matter for the correct gpio programming! how can i try to smart mangle with those gpio registers? then i'd like to say that on the flyvideo case there's an orange led off on linux and going on when i run the windows driver (could be a signal when the driver initialise and loads a firmware on the tda10046 dvb-t chip?) BTW you can see in both the dmesg log the output of an i2c_scan i put in the modprobe. there is the i2c device at address 0x10; it should be the tda10046 demod, as seen in other v4l messages.. that's all for this week. good evening andrea venturi
