Hi, I have exactly the same problem with a KNC-One-Card running on debian sarge. As far as I know the KNC-One-Card (without "plus") is exactly the same card as the Terratec 1200 DVB-T mentioned by Henrik. i have tested the following kernels: - 2.6.10 from debian unstable - 2.6.10 selfcompiled - 2.6.10 with the patch supplied by alexander riedel last week on this list. With a channels.conf that "scan" produced with a CinergyT2-USB-Box - which i had temporarily connected to the same machine - even VDR works well with the KNC-One-Card! But I cannot get "scan" to find a single station using the KNC-One-Card. Any suggestions? Best regards Karsten Henrik J?nsson wrote: > Hi > I'm trying to get my terratec dvb-t card to work under SUSE 9.2 with > kernel 2.6.11.3. But i can't get it to find any channels. > this is how it looks when i do dmesg > > Linux video capture interface: v1.00 > saa7146: register extension 'dvb'. > saa7146: register extension 'budget dvb'. > saa7146: register extension 'budget_ci dvb'. > saa7146: register extension 'budget dvb /w video in'. > ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 19 (level, low) -> IRQ 217 > saa7146: found saa7146 @ mem ffffc20000842000 (revision 1, irq 217) > (0x153b,0x1157). > DVB: registering new adapter (Terratec Cinergy 1200 DVB-T). > adapter failed MAC signature check > encoded MAC from EEPROM was > ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff > KNC1-0: MAC addr = 00:0a:ac:01:a4:ef > DVB: registering frontend 0 (Philips TDA10046H DVB-T)... > ciintf_init: CI interface initialised > > with ./scan dvb-t/se-Emmaboda > channels.conf > i get this > > scanning dvb-t/se-Emmaboda > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > initial transponder 474000000 0 2 0 3 1 2 0 > initial transponder 530000000 0 2 0 3 1 2 0 > initial transponder 674000000 0 2 0 3 1 2 0 > initial transponder 730000000 0 2 0 3 1 2 0 > >>> tune to: > 474000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > WARNING: >>> tuning failed!!! > >>> tune to: > 474000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > (tuning failed) > WARNING: >>> tuning failed!!! > >>> tune to: > 530000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > WARNING: >>> tuning failed!!! > >>> tune to: > 530000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > (tuning failed) > WARNING: >>> tuning failed!!! > >>> tune to: > 674000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > WARNING: >>> tuning failed!!! > >>> tune to: > 674000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > (tuning failed) > WARNING: >>> tuning failed!!! > >>> tune to: > 730000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > > WARNING: >>> tuning failed!!! > >>> tune to: > 730000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > (tuning failed) > WARNING: >>> tuning failed!!! > ERROR: initial tuning failed > dumping lists (0 services) > Done. > > is there anyone out there that can help me? > // Henrik > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
