I posted it. Just some lines below. As you see dvb_bt8xx is loaded. Regards, Roberto Il giorno sab, 19-02-2005 alle 16:23 +0100, Sebastian Frei ha scritto: > Am Samstag 19 Februar 2005 15:43 schrieb Roberto Sebastiano: > > Hi, > > I have a Twinhan DTV Express I bought a couple of days ago, but > > currently, I have problems getting it working properly. > > > > Previously I had a Skystar2 that worked without problems. > > > > > > Now, for the Twinhan I have this modules loaded (linux 2.6.10): > > newdeal:/home/robs# lsmod > > Module Size Used by > > dvb_bt8xx 10244 0 > > mt352 5700 1 dvb_bt8xx > > dst 13192 1 dvb_bt8xx > > bt878 10936 2 dvb_bt8xx,dst > > tuner 21796 0 > > bttv 153680 2 dvb_bt8xx,bt878 > > video_buf 22020 1 bttv > > btcx_risc 4808 1 bttv > > 8139too 24832 0 > > rtc 12664 0 > > > > And dmesg says: > > > > bttv: driver version 0.9.15 loaded > > bttv: using 8 buffers with 2080k (520 pages) each for capture > > bttv: Bt8xx card found (0). > > bttv0: Bt878 (rev 17) at 0000:01:09.0, irq: 5, latency: 32, mmio: > > 0xc0000000 > > bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID > > is 1822:0001 > > bttv0: using: Twinhan DST + clones [card=113,autodetected] > > bttv0: gpio: en=00000000, out=00000000 in=00f500fe [init] > > bttv0: using tuner=4 > > bttv0: add subdevice "dvb0" > > bt878: AUDIO driver version 0.0.0 loaded > > bt878: Bt878 AUDIO function found (0). > > bt878(0): Bt878 (rev 17) at 01:09.1, irq: 5, latency: 32, memory: > > 0xc0001000 > > DVB: registering new adapter (bttv0). > > dst_check_ci: recognize DST-03T > > DST type : satellite > > DST type flags : 0x2 ts204 0x4 symdiv > > DVB: registering frontend 0 (DST DVB-S)... > > > > Note the line bttv0 detected .. "DVB-T" .. maybe the card is getting > > detected incorrectly ? > > That's no problem, your card is detected correctly. Did you load the dvb_bt8xx > module ? It's necessary. > > > > > > > This is lspci: > > <snip> > > 0000:01:09.0 Multimedia video controller: Brooktree Corporation Bt878 > > Video Capture (rev 11) > > 0000:01:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio > > Capture (rev 11) > > > > The card is exactly a "Twinhan DTV Sat-Express" (DVB-S), as stated on > > the box > > > > > > I have a channels.conf in the .mplayer directory, but I get this: > > > > newdeal:/home/robs# mplayer "dvb://Italia 1" > > MPlayer 1.0pre6-3.3.5 (C) 2000-2004 MPlayer Team > > CPU: Advanced Micro Devices Athlon MP/XP/XP-M Barton (Family: 6, > > Stepping: 0) > > <snip> > > Playing dvb://Italia 1. > > code taken from dvbstream for mplayer v0.4pre1 - (C) Dave Chapman 2001 > > Released under the GPL. > > Latest version available from http://www.linuxstb.org/ > > dvb_tune Freq: 11919000 > > DISEQC SETTING FAILED > > dvb_tune, TUNING FAILED > > ERROR, COULDN'T SET CHANNEL 947: Failed to open dvb://Italia 1 > > > > Exiting... (End of file) > > > > > > The same with xine (but it exits with a less meaningfull message) > > > > > > I can only see the sat channels doing: > > newdeal:/home/robs# szap -r "Italia 1" > > reading channels from file '/root/.szap/channels.conf' zapping to 948 > > 'Italia 1': > > sat 0, frequency = 11919 MHz V, symbolrate 27500000, vpid = 0x0200, > > apid= 0x028a > > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > > FE_DISEQC_SEND_BURST failed: Operation not supported > > status 00 | signal 0000 | snr 0000 | ber fffffffe | unc fffffffe | > > status 1f | signal 2800 | snr 1f2c | ber fffffffe | unc fffffffe | > > FE_HAS_LOCK > > > > and on another terminal: > > newdeal:/home/robs# mplayer /dev/dvb/adapter0/dvr0 > > MPlayer 1.0pre6-3.3.5 (C) 2000-2004 MPlayer Team > > <snip> > > Playing /dev/dvb/adapter0/dvr0. > > Cache fill: 0,00% (0 bytes) TS file format detected. > > DEMUX OPEN, AUDIO_ID: -1, VIDEO_ID: -1, SUBTITLE_ID: -1, > > PROBING UP TO 2000000, PROG: 0 > > VIDEO MPEG2(pid=512)...AUDIO MPA(pid=650) NO SUBS (yet)! PROGRAM N. 0 > > Opened TS demuxer, audio: 50(pid 650), video: 10000002(pid > > 512)...POS=7332 > > VIDEO: MPEG2 704x576 (aspect 2) 25,000 fps 15000,0 kbps (1875,0 > > kbyte/s) > > ========================================================================== > > Trying to force audio codec driver family libmad... > > Opening audio decoder: [libmad] libmad mpeg audio decoder > > AUDIO: 48000 Hz, 2 ch, 16 bit (0x10), ratio: 32000->192000 (256,0 kbit) > > Selected audio codec: [mad] afm:libmad (libMAD MPEG layer 1-2-3) > > ========================================================================== > > vo: X11 running at 1280x1024 with depth 24 and 32 bpp (":0.0" => local > > display) > > ========================================================================== > > Opening video decoder: [mpegpes] MPEG 1/2 Video passthrough > > VDec: vo config request - 704 x 576 (preferred csp: Mpeg PES) > > Could not find matching colorspace - retrying with -vf scale... > > Opening video filter: [scale] > > The selected video_out device is incompatible with this codec. > > VDecoder init failed :( > > Opening video decoder: [libmpeg2] MPEG 1/2 Video decoder > > libmpeg2-v0.4.0b > > Selected video codec: [mpeg12] vfm:libmpeg2 (MPEG 1 or 2 (libmpeg2)) > > ========================================================================== > > Checking audio filter chain for 48000Hz/2ch/16bit -> > > 48000Hz/2ch/16bit... > > AF_pre: af format: 2 bps, 2 ch, 48000 hz, little endian signed int > > AF_pre: 48000Hz 2ch Signed 16-bit (Little-Endian) > > alsa-init: got device=0, subdevice=0 > > alsa-init: 1 soundcard found, using: default > > alsa: 48000 Hz/2 channels/4 bpf/65536 bytes buffer/Signed 16 bit Little > > Endian > > AO: [alsa] 48000Hz 2ch Signed 16-bit (Little-Endian) (2 bps) > > Building audio filter chain for 48000Hz/2ch/16bit -> > > 48000Hz/2ch/16bit... > > Starting playback... > > VDec: vo config request - 704 x 576 (preferred csp: Planar YV12) > > VDec: using Planar YV12 as output csp (no 0) > > Movie-Aspect is 1,33:1 - prescaling to correct movie aspect. > > VO: [x11] 704x576 => 768x576 Planar YV12 > > SwScaler: using unscaled Planar YV12 -> BGRA special converter > > alsa-uninit: pcm closed: -0,327 ct: -0,188 52/ 52 14% 11% 1,7% 0 0 > > 18% > > > > > > Any clue ? > > > I don't use mplayer for watching DVB, so I don't know what causes your > problem. Post the output of lsmod, please. > > S. > > > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
