Hi, I have a Twinhan DTV Express I bought a couple of days ago, but currently, I have problems getting it working properly. Previously I had a Skystar2 that worked without problems. Now, for the Twinhan I have this modules loaded (linux 2.6.10): newdeal:/home/robs# lsmod Module Size Used by dvb_bt8xx 10244 0 mt352 5700 1 dvb_bt8xx dst 13192 1 dvb_bt8xx bt878 10936 2 dvb_bt8xx,dst tuner 21796 0 bttv 153680 2 dvb_bt8xx,bt878 video_buf 22020 1 bttv btcx_risc 4808 1 bttv 8139too 24832 0 rtc 12664 0 And dmesg says: bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:01:09.0, irq: 5, latency: 32, mmio: 0xc0000000 bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00f500fe [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). bt878(0): Bt878 (rev 17) at 01:09.1, irq: 5, latency: 32, memory: 0xc0001000 DVB: registering new adapter (bttv0). dst_check_ci: recognize DST-03T DST type : satellite DST type flags : 0x2 ts204 0x4 symdiv DVB: registering frontend 0 (DST DVB-S)... Note the line bttv0 detected .. "DVB-T" .. maybe the card is getting detected incorrectly ? This is lspci: <snip> 0000:01:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 0000:01:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) The card is exactly a "Twinhan DTV Sat-Express" (DVB-S), as stated on the box I have a channels.conf in the .mplayer directory, but I get this: newdeal:/home/robs# mplayer "dvb://Italia 1" MPlayer 1.0pre6-3.3.5 (C) 2000-2004 MPlayer Team CPU: Advanced Micro Devices Athlon MP/XP/XP-M Barton (Family: 6, Stepping: 0) <snip> Playing dvb://Italia 1. code taken from dvbstream for mplayer v0.4pre1 - (C) Dave Chapman 2001 Released under the GPL. Latest version available from http://www.linuxstb.org/ dvb_tune Freq: 11919000 DISEQC SETTING FAILED dvb_tune, TUNING FAILED ERROR, COULDN'T SET CHANNEL 947: Failed to open dvb://Italia 1 Exiting... (End of file) The same with xine (but it exits with a less meaningfull message) I can only see the sat channels doing: newdeal:/home/robs# szap -r "Italia 1" reading channels from file '/root/.szap/channels.conf' zapping to 948 'Italia 1': sat 0, frequency = 11919 MHz V, symbolrate 27500000, vpid = 0x0200, apid= 0x028a using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' FE_DISEQC_SEND_BURST failed: Operation not supported status 00 | signal 0000 | snr 0000 | ber fffffffe | unc fffffffe | status 1f | signal 2800 | snr 1f2c | ber fffffffe | unc fffffffe | FE_HAS_LOCK and on another terminal: newdeal:/home/robs# mplayer /dev/dvb/adapter0/dvr0 MPlayer 1.0pre6-3.3.5 (C) 2000-2004 MPlayer Team <snip> Playing /dev/dvb/adapter0/dvr0. Cache fill: 0,00% (0 bytes) TS file format detected. DEMUX OPEN, AUDIO_ID: -1, VIDEO_ID: -1, SUBTITLE_ID: -1, PROBING UP TO 2000000, PROG: 0 VIDEO MPEG2(pid=512)...AUDIO MPA(pid=650) NO SUBS (yet)! PROGRAM N. 0 Opened TS demuxer, audio: 50(pid 650), video: 10000002(pid 512)...POS=7332 VIDEO: MPEG2 704x576 (aspect 2) 25,000 fps 15000,0 kbps (1875,0 kbyte/s) ========================================================================== Trying to force audio codec driver family libmad... Opening audio decoder: [libmad] libmad mpeg audio decoder AUDIO: 48000 Hz, 2 ch, 16 bit (0x10), ratio: 32000->192000 (256,0 kbit) Selected audio codec: [mad] afm:libmad (libMAD MPEG layer 1-2-3) ========================================================================== vo: X11 running at 1280x1024 with depth 24 and 32 bpp (":0.0" => local display) ========================================================================== Opening video decoder: [mpegpes] MPEG 1/2 Video passthrough VDec: vo config request - 704 x 576 (preferred csp: Mpeg PES) Could not find matching colorspace - retrying with -vf scale... Opening video filter: [scale] The selected video_out device is incompatible with this codec. VDecoder init failed :( Opening video decoder: [libmpeg2] MPEG 1/2 Video decoder libmpeg2-v0.4.0b Selected video codec: [mpeg12] vfm:libmpeg2 (MPEG 1 or 2 (libmpeg2)) ========================================================================== Checking audio filter chain for 48000Hz/2ch/16bit -> 48000Hz/2ch/16bit... AF_pre: af format: 2 bps, 2 ch, 48000 hz, little endian signed int AF_pre: 48000Hz 2ch Signed 16-bit (Little-Endian) alsa-init: got device=0, subdevice=0 alsa-init: 1 soundcard found, using: default alsa: 48000 Hz/2 channels/4 bpf/65536 bytes buffer/Signed 16 bit Little Endian AO: [alsa] 48000Hz 2ch Signed 16-bit (Little-Endian) (2 bps) Building audio filter chain for 48000Hz/2ch/16bit -> 48000Hz/2ch/16bit... Starting playback... VDec: vo config request - 704 x 576 (preferred csp: Planar YV12) VDec: using Planar YV12 as output csp (no 0) Movie-Aspect is 1,33:1 - prescaling to correct movie aspect. VO: [x11] 704x576 => 768x576 Planar YV12 SwScaler: using unscaled Planar YV12 -> BGRA special converter alsa-uninit: pcm closed: -0,327 ct: -0,188 52/ 52 14% 11% 1,7% 0 0 18% Any clue ? Thanks, Roberto Sebastiano
