Am Freitag, den 06.01.2017, 18:11 -0800 schrieb Steve Longerbeam:
> Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
> Both hang off the same i2c2 bus, so they require different (and non-
> default) i2c slave addresses.
>
> The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
>
> The OV5640 connects to the input port on the MIPI CSI-2 receiver on
> mipi_csi. It is set to transmit over MIPI virtual channel 1.
>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
> ---
> arch/arm/boot/dts/imx6dl-sabrelite.dts | 5 ++
> arch/arm/boot/dts/imx6q-sabrelite.dts | 6 ++
> arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 118 +++++++++++++++++++++++++++++++
> 3 files changed, 129 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/imx6dl-sabrelite.dts
> index 0f06ca5..fec2524 100644
> --- a/arch/arm/boot/dts/imx6dl-sabrelite.dts
> +++ b/arch/arm/boot/dts/imx6dl-sabrelite.dts
> @@ -48,3 +48,8 @@
> model = "Freescale i.MX6 DualLite SABRE Lite Board";
> compatible = "fsl,imx6dl-sabrelite", "fsl,imx6dl";
> };
> +
> +&ipu1_csi1_from_ipu1_csi1_mux {
> + data-lanes = <0 1>;
> + clock-lanes = <2>;
> +};
> diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
> index 66d10d8..9e2d26d 100644
> --- a/arch/arm/boot/dts/imx6q-sabrelite.dts
> +++ b/arch/arm/boot/dts/imx6q-sabrelite.dts
> @@ -52,3 +52,9 @@
> &sata {
> status = "okay";
> };
> +
> +&ipu1_csi1_from_mipi_vc1 {
> + data-lanes = <0 1>;
> + clock-lanes = <2>;
> +};
> +
> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> index 795b5a5..bca9fed 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> @@ -39,6 +39,8 @@
> * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> * OTHER DEALINGS IN THE SOFTWARE.
> */
> +
> +#include <dt-bindings/clock/imx6qdl-clock.h>
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/input/input.h>
>
> @@ -96,6 +98,15 @@
> };
> };
>
> + mipi_xclk: mipi_xclk {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <22000000>;
> + clock-output-names = "mipi_pwm3";
> + pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
> + status = "okay";
> + };
> +
> gpio-keys {
> compatible = "gpio-keys";
> pinctrl-names = "default";
> @@ -220,6 +231,22 @@
> };
> };
>
> +&ipu1_csi0_from_ipu1_csi0_mux {
> + bus-width = <8>;
> + data-shift = <12>; /* Lines 19:12 used */
> + hsync-active = <1>;
> + vync-active = <1>;
> +};
> +
> +&ipu1_csi0_mux_from_parallel_sensor {
> + remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
> +};
> +
> +&ipu1_csi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1_csi0>;
> +};
> +
> &audmux {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_audmux>;
> @@ -299,6 +326,52 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_i2c2>;
> status = "okay";
> +
> + ov5640: camera@40 {
> + compatible = "ovti,ov5640";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5640>;
> + clocks = <&mipi_xclk>;
> + clock-names = "xclk";
> + reg = <0x40>;
> + xclk = <22000000>;
This is superfluous, you can use clk_get_rate on mipi_xclk.
> + reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
> + pwdn-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ov5640_to_mipi_csi: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&mipi_csi_from_mipi_sensor>;
> + data-lanes = <0 1>;
> + clock-lanes = <2>;
> + };
> + };
> + };
> +
> + ov5642: camera@42 {
> + compatible = "ovti,ov5642";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5642>;
> + clocks = <&clks IMX6QDL_CLK_CKO2>;
> + clock-names = "xclk";
> + reg = <0x42>;
> + xclk = <24000000>;
Same here, use assigned-clock-rates on IMX6QDL_CLK_CKO2 if necessary.
> + reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
> + pwdn-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
> + gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + ov5642_to_ipu1_csi0_mux: endpoint {
> + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> + bus-width = <8>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + };
> + };
> + };
> };
>
> &i2c3 {
> @@ -412,6 +485,23 @@
> >;
> };
>
> + pinctrl_ipu1_csi0: ipu1csi0grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0
> + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0
> + MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x1b0b0
> + >;
> + };
> +
> pinctrl_j15: j15grp {
> fsl,pins = <
> MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
> @@ -445,6 +535,22 @@
> >;
> };
>
> + pinctrl_ov5640: ov5640grp {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x000b0
> + MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
> + >;
> + };
> +
> + pinctrl_ov5642: ov5642grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
> + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x130b0
> + MX6QDL_PAD_GPIO_3__CCM_CLKO2 0x000b0
> + >;
> + };
> +
> pinctrl_pwm1: pwm1grp {
> fsl,pins = <
> MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
> @@ -601,3 +707,15 @@
> vmmc-supply = <®_3p3v>;
> status = "okay";
> };
> +
> +&mipi_csi {
> + status = "okay";
> +};
> +
> +/* Incoming port from sensor */
> +&mipi_csi_from_mipi_sensor {
> + remote-endpoint = <&ov5640_to_mipi_csi>;
> + data-lanes = <0 1>;
> + clock-lanes = <2>;
> +};
> +
regards
Philipp
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
