Fix checkpatch.pl warning:
Block comments use * on subsequent lines
Block comments use a trailing */ on a separate line
Signed-off-by: Anson Jacob <ansonjacob.aj@xxxxxxxxx>
---
drivers/staging/fbtft/fb_st7735r.c | 43 +++++++++++++++++++++++---------------
1 file changed, 26 insertions(+), 17 deletions(-)
diff --git a/drivers/staging/fbtft/fb_st7735r.c b/drivers/staging/fbtft/fb_st7735r.c
index c5e51fe..6670f2b 100644
--- a/drivers/staging/fbtft/fb_st7735r.c
+++ b/drivers/staging/fbtft/fb_st7735r.c
@@ -33,35 +33,43 @@ static int default_init_sequence[] = {
-2, 500, /* delay */
/* FRMCTR1 - frame rate control: normal mode
- frame rate = fosc / (1 x 2 + 40) * (LINE + 2C + 2D) */
+ * frame rate = fosc / (1 x 2 + 40) * (LINE + 2C + 2D)
+ */
-1, 0xB1, 0x01, 0x2C, 0x2D,
/* FRMCTR2 - frame rate control: idle mode
- frame rate = fosc / (1 x 2 + 40) * (LINE + 2C + 2D) */
+ * frame rate = fosc / (1 x 2 + 40) * (LINE + 2C + 2D)
+ */
-1, 0xB2, 0x01, 0x2C, 0x2D,
/* FRMCTR3 - frame rate control - partial mode
- dot inversion mode, line inversion mode */
+ * dot inversion mode, line inversion mode
+ */
-1, 0xB3, 0x01, 0x2C, 0x2D, 0x01, 0x2C, 0x2D,
/* INVCTR - display inversion control
- no inversion */
+ * no inversion
+ */
-1, 0xB4, 0x07,
/* PWCTR1 - Power Control
- -4.6V, AUTO mode */
+ * -4.6V, AUTO mode
+ */
-1, 0xC0, 0xA2, 0x02, 0x84,
/* PWCTR2 - Power Control
- VGH25 = 2.4C VGSEL = -10 VGH = 3 * AVDD */
+ * VGH25 = 2.4C VGSEL = -10 VGH = 3 * AVDD
+ */
-1, 0xC1, 0xC5,
/* PWCTR3 - Power Control
- Opamp current small, Boost frequency */
+ * Opamp current small, Boost frequency
+ */
-1, 0xC2, 0x0A, 0x00,
/* PWCTR4 - Power Control
- BCLK/2, Opamp current small & Medium low */
+ * BCLK/2, Opamp current small & Medium low
+ */
-1, 0xC3, 0x8A, 0x2A,
/* PWCTR5 - Power Control */
@@ -101,11 +109,12 @@ static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye)
static int set_var(struct fbtft_par *par)
{
/* MADCTL - Memory data access control
- RGB/BGR:
- 1. Mode selection pin SRGB
- RGB H/W pin for color filter setting: 0=RGB, 1=BGR
- 2. MADCTL RGB bit
- RGB-BGR ORDER color filter panel: 0=RGB, 1=BGR */
+ * RGB/BGR:
+ * 1. Mode selection pin SRGB
+ * RGB H/W pin for color filter setting: 0=RGB, 1=BGR
+ * 2. MADCTL RGB bit
+ * RGB-BGR ORDER color filter panel: 0=RGB, 1=BGR
+ */
switch (par->info->var.rotate) {
case 0:
write_reg(par, MIPI_DCS_SET_ADDRESS_MODE,
@@ -129,10 +138,10 @@ static int set_var(struct fbtft_par *par)
}
/*
- Gamma string format:
- VRF0P VOS0P PK0P PK1P PK2P PK3P PK4P PK5P PK6P PK7P PK8P PK9P SELV0P SELV1P SELV62P SELV63P
- VRF0N VOS0N PK0N PK1N PK2N PK3N PK4N PK5N PK6N PK7N PK8N PK9N SELV0N SELV1N SELV62N SELV63N
-*/
+ * Gamma string format:
+ * VRF0P VOS0P PK0P PK1P PK2P PK3P PK4P PK5P PK6P PK7P PK8P PK9P SELV0P SELV1P SELV62P SELV63P
+ * VRF0N VOS0N PK0N PK1N PK2N PK3N PK4N PK5N PK6N PK7N PK8N PK9N SELV0N SELV1N SELV62N SELV63N
+ */
#define CURVE(num, idx) curves[num * par->gamma.num_values + idx]
static int set_gamma(struct fbtft_par *par, unsigned long *curves)
{
--
2.7.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
