Fix checkpatch.pl warning 'line over 80 characters'
Signed-off-by: Anson Jacob <ansonjacob.aj@xxxxxxxxx>
---
drivers/staging/comedi/drivers/ni_at_a2150.c | 82 ++++++++++++++++------------
1 file changed, 46 insertions(+), 36 deletions(-)
diff --git a/drivers/staging/comedi/drivers/ni_at_a2150.c b/drivers/staging/comedi/drivers/ni_at_a2150.c
index 957fb9f..3c00de1 100644
--- a/drivers/staging/comedi/drivers/ni_at_a2150.c
+++ b/drivers/staging/comedi/drivers/ni_at_a2150.c
@@ -58,41 +58,49 @@
/* Registers and bits */
#define CONFIG_REG 0x0
-#define CHANNEL_BITS(x) ((x) & 0x7)
-#define CHANNEL_MASK 0x7
-#define CLOCK_SELECT_BITS(x) (((x) & 0x3) << 3)
-#define CLOCK_DIVISOR_BITS(x) (((x) & 0x3) << 5)
-#define CLOCK_MASK (0xf << 3)
-#define ENABLE0_BIT 0x80 /* enable (don't internally ground) channels 0 and 1 */
-#define ENABLE1_BIT 0x100 /* enable (don't internally ground) channels 2 and 3 */
-#define AC0_BIT 0x200 /* ac couple channels 0,1 */
-#define AC1_BIT 0x400 /* ac couple channels 2,3 */
-#define APD_BIT 0x800 /* analog power down */
-#define DPD_BIT 0x1000 /* digital power down */
-#define TRIGGER_REG 0x2 /* trigger config register */
-#define POST_TRIGGER_BITS 0x2
-#define DELAY_TRIGGER_BITS 0x3
-#define HW_TRIG_EN 0x10 /* enable hardware trigger */
-#define FIFO_START_REG 0x6 /* software start aquistion trigger */
-#define FIFO_RESET_REG 0x8 /* clears fifo + fifo flags */
-#define FIFO_DATA_REG 0xa /* read data */
-#define DMA_TC_CLEAR_REG 0xe /* clear dma terminal count interrupt */
-#define STATUS_REG 0x12 /* read only */
-#define FNE_BIT 0x1 /* fifo not empty */
-#define OVFL_BIT 0x8 /* fifo overflow */
-#define EDAQ_BIT 0x10 /* end of acquisition interrupt */
-#define DCAL_BIT 0x20 /* offset calibration in progress */
-#define INTR_BIT 0x40 /* interrupt has occurred */
-#define DMA_TC_BIT 0x80 /* dma terminal count interrupt has occurred */
-#define ID_BITS(x) (((x) >> 8) & 0x3)
-#define IRQ_DMA_CNTRL_REG 0x12 /* write only */
-#define DMA_CHAN_BITS(x) ((x) & 0x7) /* sets dma channel */
-#define DMA_EN_BIT 0x8 /* enables dma */
-#define IRQ_LVL_BITS(x) (((x) & 0xf) << 4) /* sets irq level */
-#define FIFO_INTR_EN_BIT 0x100 /* enable fifo interrupts */
-#define FIFO_INTR_FHF_BIT 0x200 /* interrupt fifo half full */
-#define DMA_INTR_EN_BIT 0x800 /* enable interrupt on dma terminal count */
-#define DMA_DEM_EN_BIT 0x1000 /* enables demand mode dma */
+#define CHANNEL_BITS(x) ((x) & 0x7)
+#define CHANNEL_MASK 0x7
+#define CLOCK_SELECT_BITS(x) (((x) & 0x3) << 3)
+#define CLOCK_DIVISOR_BITS(x) (((x) & 0x3) << 5)
+#define CLOCK_MASK (0xf << 3)
+#define ENABLE0_BIT 0x80 /* enable (don't internally ground)
+ * channels 0 and 1
+ */
+#define ENABLE1_BIT 0x100 /* enable (don't internally ground)
+ * channels 2 and 3
+ */
+#define AC0_BIT 0x200 /* ac couple channels 0,1 */
+#define AC1_BIT 0x400 /* ac couple channels 2,3 */
+#define APD_BIT 0x800 /* analog power down */
+#define DPD_BIT 0x1000 /* digital power down */
+#define TRIGGER_REG 0x2 /* trigger config register */
+#define POST_TRIGGER_BITS 0x2
+#define DELAY_TRIGGER_BITS 0x3
+#define HW_TRIG_EN 0x10 /* enable hardware trigger */
+#define FIFO_START_REG 0x6 /* software start aquistion trigger */
+#define FIFO_RESET_REG 0x8 /* clears fifo + fifo flags */
+#define FIFO_DATA_REG 0xa /* read data */
+#define DMA_TC_CLEAR_REG 0xe /* clear dma terminal count interrupt */
+#define STATUS_REG 0x12 /* read only */
+#define FNE_BIT 0x1 /* fifo not empty */
+#define OVFL_BIT 0x8 /* fifo overflow */
+#define EDAQ_BIT 0x10 /* end of acquisition interrupt */
+#define DCAL_BIT 0x20 /* offset calibration in progress */
+#define INTR_BIT 0x40 /* interrupt has occurred */
+#define DMA_TC_BIT 0x80 /* dma terminal count interrupt has
+ * occurred
+ */
+#define ID_BITS(x) (((x) >> 8) & 0x3)
+#define IRQ_DMA_CNTRL_REG 0x12 /* write only */
+#define DMA_CHAN_BITS(x) ((x) & 0x7) /* sets dma channel */
+#define DMA_EN_BIT 0x8 /* enables dma */
+#define IRQ_LVL_BITS(x) (((x) & 0xf) << 4) /* sets irq level */
+#define FIFO_INTR_EN_BIT 0x100 /* enable fifo interrupts */
+#define FIFO_INTR_FHF_BIT 0x200 /* interrupt fifo half full */
+#define DMA_INTR_EN_BIT 0x800 /* enable interrupt on dma terminal
+ * count
+ */
+#define DMA_DEM_EN_BIT 0x1000 /* enables demand mode dma */
#define I8253_BASE_REG 0x14
struct a2150_board {
@@ -550,7 +558,9 @@ static int a2150_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
if (cmd->start_src == TRIG_EXT) {
trigger_bits |= HW_TRIG_EN;
} else if (cmd->start_src == TRIG_OTHER) {
- /* XXX add support for level/slope start trigger using TRIG_OTHER */
+ /* XXX add support for level/slope start trigger
+ * using TRIG_OTHER
+ */
dev_err(dev->class_dev, "you shouldn't see this?\n");
}
/* send trigger config bits */
--
2.7.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
