Defining DEBUG_DIO simply enables some function trace messages. These are
just added noise. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@xxxxxxxxxxxxxxxxxxx>
Reviewed-by: Ian Abbott <abbotti@xxxxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/staging/comedi/drivers/ni_mio_common.c | 22 ++--------------------
1 file changed, 2 insertions(+), 20 deletions(-)
diff --git a/drivers/staging/comedi/drivers/ni_mio_common.c b/drivers/staging/comedi/drivers/ni_mio_common.c
index f44013c..4bf0ef2 100644
--- a/drivers/staging/comedi/drivers/ni_mio_common.c
+++ b/drivers/staging/comedi/drivers/ni_mio_common.c
@@ -3798,10 +3798,6 @@ static int ni_serial_insn_config(struct comedi_device *dev,
switch (data[0]) {
case INSN_CONFIG_SERIAL_CLOCK:
-
-#ifdef DEBUG_DIO
- printk("SPI serial clock Config cd\n", data[1]);
-#endif
devpriv->serial_hw_mode = 1;
devpriv->dio_control |= DIO_HW_Serial_Enable;
@@ -3890,10 +3886,6 @@ static int ni_serial_hw_readwrite8(struct comedi_device *dev,
unsigned int status1;
int err = 0, count = 20;
-#ifdef DEBUG_DIO
- printk("ni_serial_hw_readwrite8: outputting 0x%x\n", data_out);
-#endif
-
devpriv->dio_output &= ~DIO_Serial_Data_Mask;
devpriv->dio_output |= DIO_Serial_Data_Out(data_out);
devpriv->stc_writew(dev, devpriv->dio_output, DIO_Output_Register);
@@ -3927,12 +3919,8 @@ static int ni_serial_hw_readwrite8(struct comedi_device *dev,
DIO_Serial_IO_In_Progress_St goes high one bit too early. */
udelay((devpriv->serial_interval_ns + 999) / 1000);
- if (data_in != NULL) {
+ if (data_in != NULL)
*data_in = devpriv->stc_readw(dev, DIO_Serial_Input_Register);
-#ifdef DEBUG_DIO
- printk("ni_serial_hw_readwrite8: inputted 0x%x\n", *data_in);
-#endif
- }
Error:
devpriv->stc_writew(dev, devpriv->dio_control, DIO_Control_Register);
@@ -3948,10 +3936,6 @@ static int ni_serial_sw_readwrite8(struct comedi_device *dev,
struct ni_private *devpriv = dev->private;
unsigned char mask, input = 0;
-#ifdef DEBUG_DIO
- printk("ni_serial_sw_readwrite8: outputting 0x%x\n", data_out);
-#endif
-
/* Wait for one bit before transfer */
udelay((devpriv->serial_interval_ns + 999) / 1000);
@@ -3988,9 +3972,7 @@ static int ni_serial_sw_readwrite8(struct comedi_device *dev,
input |= mask;
}
}
-#ifdef DEBUG_DIO
- printk("ni_serial_sw_readwrite8: inputted 0x%x\n", input);
-#endif
+
if (data_in)
*data_in = input;
--
1.8.4.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
