On Fri, 20 Apr 2018 20:41:52 -0400
Brian Masney <masneyb@xxxxxxxxxxxxx> wrote:
> This patch removes several unnecessary comments, changes some comments
> so that the use as much of the allowable 80 characters as possible, adds
> the proper whitespace, removes some structure members from the kernel
> docs that are no longer present, and improves the existing kernel doc
> information for some existing structure members.
>
> Signed-off-by: Brian Masney <masneyb@xxxxxxxxxxxxx>
Looks sensible
Applied,
Thanks,
Jonathan
> ---
> drivers/staging/iio/light/tsl2x7x.c | 59 +++++++++++++++++--------------------
> drivers/staging/iio/light/tsl2x7x.h | 48 +++++++++++++++---------------
> 2 files changed, 51 insertions(+), 56 deletions(-)
>
> diff --git a/drivers/staging/iio/light/tsl2x7x.c b/drivers/staging/iio/light/tsl2x7x.c
> index 293810ff11b9..05c0f3d5fac0 100644
> --- a/drivers/staging/iio/light/tsl2x7x.c
> +++ b/drivers/staging/iio/light/tsl2x7x.c
> @@ -1,6 +1,6 @@
> /*
> - * Device driver for monitoring ambient light intensity in (lux)
> - * and proximity detection (prox) within the TAOS TSL2X7X family of devices.
> + * Device driver for monitoring ambient light intensity in (lux) and proximity
> + * detection (prox) within the TAOS TSL2X7X family of devices.
> *
> * Copyright (c) 2012, TAOS Corporation.
> * Copyright (c) 2017-2018 Brian Masney <masneyb@xxxxxxxxxxxxx>
> @@ -21,7 +21,7 @@
> #include <linux/iio/sysfs.h>
> #include "tsl2x7x.h"
>
> -/* Cal defs*/
> +/* Cal defs */
> #define PROX_STAT_CAL 0
> #define PROX_STAT_SAMP 1
> #define MAX_SAMPLES_CAL 200
> @@ -34,10 +34,11 @@
> /* Lux calculation constants */
> #define TSL2X7X_LUX_CALC_OVER_FLOW 65535
>
> -/* TAOS Register definitions - note:
> - * depending on device, some of these register are not used and the
> - * register address is benign.
> +/*
> + * TAOS Register definitions - Note: depending on device, some of these register
> + * are not used and the register address is benign.
> */
> +
> /* 2X7X register offsets */
> #define TSL2X7X_MAX_CONFIG_REG 16
>
> @@ -342,15 +343,14 @@ static int tsl2x7x_read_autoinc_regs(struct tsl2X7X_chip *chip, int lower_reg,
> * @indio_dev: pointer to IIO device
> *
> * The raw ch0 and ch1 values of the ambient light sensed in the last
> - * integration cycle are read from the device.
> - * Time scale factor array values are adjusted based on the integration time.
> - * The raw values are multiplied by a scale factor, and device gain is obtained
> - * using gain index. Limit checks are done next, then the ratio of a multiple
> - * of ch1 value, to the ch0 value, is calculated. Array tsl2x7x_device_lux[]
> - * is then scanned to find the first ratio value that is just above the ratio
> - * we just calculated. The ch0 and ch1 multiplier constants in the array are
> - * then used along with the time scale factor array values, to calculate the
> - * lux.
> + * integration cycle are read from the device. Time scale factor array values
> + * are adjusted based on the integration time. The raw values are multiplied
> + * by a scale factor, and device gain is obtained using gain index. Limit
> + * checks are done next, then the ratio of a multiple of ch1 value, to the
> + * ch0 value, is calculated. Array tsl2x7x_device_lux[] is then scanned to
> + * find the first ratio value that is just above the ratio we just calculated.
> + * The ch0 and ch1 multiplier constants in the array are then used along with
> + * the time scale factor array values, to calculate the lux.
> */
> static int tsl2x7x_get_lux(struct iio_dev *indio_dev)
> {
> @@ -363,7 +363,6 @@ static int tsl2x7x_get_lux(struct iio_dev *indio_dev)
> mutex_lock(&chip->als_mutex);
>
> if (chip->tsl2x7x_chip_status != TSL2X7X_CHIP_WORKING) {
> - /* device is not enabled */
> dev_err(&chip->client->dev, "%s: device is not enabled\n",
> __func__);
> ret = -EBUSY;
> @@ -374,7 +373,6 @@ static int tsl2x7x_get_lux(struct iio_dev *indio_dev)
> if (ret < 0)
> goto out_unlock;
>
> - /* is data new & valid */
> if (!(ret & TSL2X7X_STA_ADC_VALID)) {
> dev_err(&chip->client->dev,
> "%s: data not valid yet\n", __func__);
> @@ -430,12 +428,12 @@ static int tsl2x7x_get_lux(struct iio_dev *indio_dev)
> lux = (lux + (chip->als_time_scale >> 1)) /
> chip->als_time_scale;
>
> - /* adjust for active gain scale
> - * The tsl2x7x_device_lux tables have a factor of 256 built-in.
> - * User-specified gain provides a multiplier.
> + /*
> + * adjust for active gain scale. The tsl2x7x_device_lux tables have a
> + * factor of 256 built-in. User-specified gain provides a multiplier.
> * Apply user-specified gain before shifting right to retain precision.
> - * Use 64 bits to avoid overflow on multiplication.
> - * Then go back to 32 bits before division to avoid using div_u64().
> + * Use 64 bits to avoid overflow on multiplication. Then go back to
> + * 32 bits before division to avoid using div_u64().
> */
>
> lux64 = lux;
> @@ -713,14 +711,13 @@ static int tsl2x7x_chip_off(struct iio_dev *indio_dev)
> }
>
> /**
> - * tsl2x7x_invoke_change
> + * tsl2x7x_invoke_change - power cycle the device to implement the user
> + * parameters
> * @indio_dev: pointer to IIO device
> *
> - * Obtain and lock both ALS and PROX resources,
> - * determine and save device state (On/Off),
> - * cycle device to implement updated parameter,
> - * put device back into proper state, and unlock
> - * resource.
> + * Obtain and lock both ALS and PROX resources, determine and save device state
> + * (On/Off), cycle device to implement updated parameter, put device back into
> + * proper state, and unlock resource.
> */
> static int tsl2x7x_invoke_change(struct iio_dev *indio_dev)
> {
> @@ -895,7 +892,8 @@ static ssize_t in_illuminance0_lux_table_store(struct device *dev,
>
> get_options(buf, ARRAY_SIZE(value), value);
>
> - /* We now have an array of ints starting at value[1], and
> + /*
> + * We now have an array of ints starting at value[1], and
> * enumerated by value[0].
> * We expect each group of three ints is one table entry,
> * and the last table entry is all 0.
> @@ -1643,9 +1641,7 @@ static int tsl2x7x_probe(struct i2c_client *clientp,
> }
> }
>
> - /* Load up the defaults */
> tsl2x7x_defaults(chip);
> - /* Make sure the chip is on */
> tsl2x7x_chip_on(indio_dev);
>
> ret = iio_device_register(indio_dev);
> @@ -1719,7 +1715,6 @@ static const struct dev_pm_ops tsl2x7x_pm_ops = {
> .resume = tsl2x7x_resume,
> };
>
> -/* Driver definition */
> static struct i2c_driver tsl2x7x_driver = {
> .driver = {
> .name = "tsl2x7x",
> diff --git a/drivers/staging/iio/light/tsl2x7x.h b/drivers/staging/iio/light/tsl2x7x.h
> index 408e5a89edb1..85d8fe7a94c8 100644
> --- a/drivers/staging/iio/light/tsl2x7x.h
> +++ b/drivers/staging/iio/light/tsl2x7x.h
> @@ -36,32 +36,35 @@ struct tsl2x7x_lux {
> #define TSL2X7X_MAX_TIMER_CNT 0xFF
>
> /**
> - * struct tsl2x7x_default_settings - power on defaults unless
> - * overridden by platform data.
> - * @als_time: ALS Integration time - multiple of 50mS
> - * @als_gain: Index into the ALS gain table.
> - * @als_gain_trim: default gain trim to account for
> - * aperture effects.
> - * @wait_time: Time between PRX and ALS cycles
> - * in 2.7 periods
> - * @prox_time: 5.2ms prox integration time -
> - * decrease in 2.7ms periods
> - * @prox_gain: Proximity gain index
> + * struct tsl2x7x_settings - Settings for the tsl2x7x driver
> + * @als_time: Integration time of the ALS channel ADCs in 2.73 ms
> + * increments. Total integration time is
> + * (256 - als_time) * 2.73.
> + * @als_gain: Index into the tsl2x7x_als_gain array.
> + * @als_gain_trim: Default gain trim to account for aperture effects.
> + * @wait_time: Time between proximity and ALS cycles in 2.73
> + * periods.
> + * @prox_time: Integration time of the proximity ADC in 2.73 ms
> + * increments. Total integration time is
> + * (256 - prx_time) * 2.73.
> + * @prox_gain: Index into the tsl2x7x_prx_gain array.
> * @prox_config: Prox configuration filters.
> - * @als_cal_target: Known external ALS reading for
> - * calibration.
> - * @als_persistence: H/W Filters, Number of 'out of limits'
> - * ALS readings.
> + * @als_cal_target: Known external ALS reading for calibration.
> + * @als_persistence: H/W Filters, Number of 'out of limits' ALS readings.
> * @als_interrupt_en: Enable/Disable ALS interrupts
> * @als_thresh_low: CH0 'low' count to trigger interrupt.
> * @als_thresh_high: CH0 'high' count to trigger interrupt.
> - * @prox_persistence: H/W Filters, Number of 'out of limits'
> - * proximity readings.
> - * @prox_interrupt_en: Enable/Disable proximity interrupts
> + * @prox_persistence: H/W Filters, Number of 'out of limits' proximity
> + * readings.
> + * @prox_interrupt_en: Enable/Disable proximity interrupts.
> * @prox_thres_low: Low threshold proximity detection.
> - * @prox_thres_high: High threshold proximity detection
> - * @prox_pulse_count: Number if proximity emitter pulses
> - * @prox_max_samples_cal: Used for prox cal.
> + * @prox_thres_high: High threshold proximity detection.
> + * @prox_pulse_count: Number if proximity emitter pulses.
> + * @prox_max_samples_cal: The number of samples that are taken when performing
> + * a proximity calibration.
> + * @prox_diode Which diode(s) to use for driving the external
> + * LED(s) for proximity sensing.
> + * @prox_power The amount of power to use for the external LED(s).
> */
> struct tsl2x7x_settings {
> int als_time;
> @@ -88,9 +91,6 @@ struct tsl2x7x_settings {
>
> /**
> * struct tsl2X7X_platform_data - Platform callback, glass and defaults
> - * @platform_power: Suspend/resume platform callback
> - * @power_on: Power on callback
> - * @power_off: Power off callback
> * @platform_lux_table: Device specific glass coefficents
> * @platform_default_settings: Device specific power on defaults
> *
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
