Remove few unnecessary comments since the macro definitions clearly justify their purpose. Signed-off-by: Himanshu Jha <himanshujha199640@xxxxxxxxx> --- v2: -reodered patch series. drivers/staging/iio/accel/adis16201.c | 36 ----------------------------------- 1 file changed, 36 deletions(-) diff --git a/drivers/staging/iio/accel/adis16201.c b/drivers/staging/iio/accel/adis16201.c index 767ebf0..6c06c0d 100644 --- a/drivers/staging/iio/accel/adis16201.c +++ b/drivers/staging/iio/accel/adis16201.c @@ -22,96 +22,66 @@ #define ADIS16201_STARTUP_DELAY_MS 220 -/* Flash memory write count */ #define ADIS16201_FLASH_CNT 0x00 -/* Output, power supply */ #define ADIS16201_SUPPLY_OUT 0x02 -/* Output, x-axis accelerometer */ #define ADIS16201_XACCL_OUT 0x04 -/* Output, y-axis accelerometer */ #define ADIS16201_YACCL_OUT 0x06 -/* Output, auxiliary ADC input */ #define ADIS16201_AUX_ADC 0x08 -/* Output, temperature */ #define ADIS16201_TEMP_OUT 0x0A -/* Output, x-axis inclination */ #define ADIS16201_XINCL_OUT 0x0C -/* Output, y-axis inclination */ #define ADIS16201_YINCL_OUT 0x0E -/* Calibration, x-axis acceleration offset */ #define ADIS16201_XACCL_OFFS 0x10 -/* Calibration, y-axis acceleration offset */ #define ADIS16201_YACCL_OFFS 0x12 -/* x-axis acceleration scale factor */ #define ADIS16201_XACCL_SCALE 0x14 -/* y-axis acceleration scale factor */ #define ADIS16201_YACCL_SCALE 0x16 -/* Calibration, x-axis inclination offset */ #define ADIS16201_XINCL_OFFS 0x18 -/* Calibration, y-axis inclination offset */ #define ADIS16201_YINCL_OFFS 0x1A -/* x-axis inclination scale factor */ #define ADIS16201_XINCL_SCALE 0x1C -/* y-axis inclination scale factor */ #define ADIS16201_YINCL_SCALE 0x1E -/* Alarm 1 amplitude threshold */ #define ADIS16201_ALM_MAG1 0x20 -/* Alarm 2 amplitude threshold */ #define ADIS16201_ALM_MAG2 0x22 -/* Alarm 1, sample period */ #define ADIS16201_ALM_SMPL1 0x24 -/* Alarm 2, sample period */ #define ADIS16201_ALM_SMPL2 0x26 -/* Alarm control */ #define ADIS16201_ALM_CTRL 0x28 -/* Auxiliary DAC data */ #define ADIS16201_AUX_DAC 0x30 -/* General-purpose digital input/output control */ #define ADIS16201_GPIO_CTRL 0x32 -/* Miscellaneous control */ #define ADIS16201_MSC_CTRL 0x34 -/* Internal sample period (rate) control */ #define ADIS16201_SMPL_PRD 0x36 /* Operation, filter configuration */ #define ADIS16201_AVG_CNT 0x38 -/* Operation, sleep mode control */ #define ADIS16201_SLP_CNT 0x3A -/* Diagnostics, system status register */ #define ADIS16201_DIAG_STAT 0x3C -/* Operation, system command register */ #define ADIS16201_GLOB_CMD 0x3E -/* MSC_CTRL */ -/* Self-test enable */ #define ADIS16201_MSC_CTRL_SELF_TEST_EN BIT(8) /* Data-ready enable: 1 = enabled, 0 = disabled */ @@ -123,18 +93,13 @@ /* Data-ready line selection: 1 = DIO1, 0 = DIO0 */ #define ADIS16201_MSC_CTRL_DATA_RDY_DIO1 BIT(0) -/* DIAG_STAT */ -/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */ #define ADIS16201_DIAG_STAT_ALARM2 BIT(9) -/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */ #define ADIS16201_DIAG_STAT_ALARM1 BIT(8) -/* SPI communications failure */ #define ADIS16201_DIAG_STAT_SPI_FAIL_BIT 3 -/* Flash update failure */ #define ADIS16201_DIAG_STAT_FLASH_UPT_FAIL_BIT 2 /* Power supply above 3.625 V */ @@ -143,7 +108,6 @@ /* Power supply below 3.15 V */ #define ADIS16201_DIAG_STAT_POWER_LOW_BIT 0 -/* GLOB_CMD */ #define ADIS16201_GLOB_CMD_SW_RESET BIT(7) #define ADIS16201_GLOB_CMD_FACTORY_RESET BIT(1) -- 2.7.4 _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
