Stefan,
On Fri, Nov 27 2020 at 10:17, Stefan Bühler wrote:
> On 11/27/20 12:45 AM, Thomas Gleixner wrote:
>> Can you please run this as root so the Capabilities are accessible?
>
> My bad, sorry. I did intend to run it as root, but should have checked
> the output. Again see attached file.
No problem.
> 05:00.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI Express-to-PCI Bridge (rev aa) (prog-if 00 [Normal decode])
> Physical Slot: 1
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> NUMA node: 0
> Bus: primary=05, secondary=06, subordinate=06, sec-latency=64
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: fb400000-fb4fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
So the bridge would support MSI, but obviously the devices on the PCI
side do not.
> 06:00.0 Serial controller: Oxford Semiconductor Ltd OX16PCI954 (Quad 16950 UART) function 0 (Uart) (prog-if 06 [16950])
> Subsystem: Oxford Semiconductor Ltd OX16PCI954 (Quad 16950 UART) function 0 (Uart)
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 16
> NUMA node: 0
> Region 0: I/O ports at e0e0 [size=32]
> Region 1: Memory at fb407000 (32-bit, non-prefetchable) [size=4K]
> Region 2: I/O ports at e0c0 [size=32]
> Region 3: Memory at fb406000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 1
> Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
But that should still work because the boot interrupt quirk should not
affect interrupts which are routed through the IOAPIC.
Sean, any idea what's going on here?
Thanks,
tglx
