Re: [PATCH v7 1/2] dt-bindings: hwmon: Add TMP512/513

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 11/11/19 12:34 PM, etremblay@xxxxxxxxxxxxxxxxxxxx wrote:
From: Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxxx>

Document the TMP513/512 device devicetree bindings

Signed-off-by: Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxxx>
---
  .../devicetree/bindings/hwmon/ti,tmp513.yaml  | 89 +++++++++++++++++++
  1 file changed, 89 insertions(+)
  create mode 100644 Documentation/devicetree/bindings/hwmon/ti,tmp513.yaml

diff --git a/Documentation/devicetree/bindings/hwmon/ti,tmp513.yaml b/Documentation/devicetree/bindings/hwmon/ti,tmp513.yaml
new file mode 100644
index 000000000000..de4ed3645e0f
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ti,tmp513.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/hwmon/ti,tmp513.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TMP513/512 system monitor sensor
+
+maintainers:
+  - Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxxx>
+
+description: |
+  This driver implements support for Texas Instruments TMP512, and TMP513.

I think this needs some rewording. This is not a driver description, but
a system description.

+  The TMP512 (dual-channel) and TMP513 (triple-channel) are system monitors
+  that include remote sensors, a local temperature sensor, and a high-side
+  current shunt monitor. These system monitors have the capability of measuring
+  remote temperatures, on-chip temperatures, and system voltage/power/current
+  consumption.
+
+  Datasheets:
+  http://www.ti.com/lit/gpn/tmp513
+  http://www.ti.com/lit/gpn/tmp512
+
+
+properties:
+  compatible:
+    enum:
+      - ti,tmp512
+      - ti,tmp513
+
+  reg:
+    maxItems: 1
+
+  shunt-resistor-micro-ohms:
+    description: |
+      If 0, the calibration process will be skiped and the current and power
+      measurement engine will not work. Temperature and voltage measurement
+      will continue to work. The shunt value also need to respect:
+      rshunt <= pga-gain * 40 * 1000 * 1000.
+      If not, it's not possible to compute a valid calibration value.
+    default: 1000
+
+  ti,pga-gain:
+    description: |
+      The gain value for the PGA function. This is 8, 4, 2 or 1.
+      The PGA gain affect the shunt voltage range.
+      The range will be equal to: pga-gain * 40mV
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2, 4, 8]
+    default: 8
+
+  ti,bus-range-microvolt:
+    description: |
+      This is the operating range of the bus voltage in microvolt
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [16000000, 32000000]
+    default: 32000000
+
+  ti,nfactor:
+    description: |
+      Array of three(TMP513) or two(TMP512) n-Factor value for each remote
+      temperature channel.
+      See datasheet Table 11 for n-Factor range list and value interpretation.
+    allOf:
+      - $ref: /schemas/types.yaml#definitions/uint8-array
+      - minItems: 2
+        maxItems: 3
+        items:
+          default: 0
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    i2c {
+        tmp513@5c {
+            compatible = "ti,tmp513";
+            reg = <0x5C>;
+            shunt-resistor-micro-ohms = <330000>;
+            ti,bus-range-microvolt = <32000000>;
+            ti,pga-gain = <8>;
+            ti,nfactor = [01 F3 00];
+        };
+    };





[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux