On Tue, Sep 25, 2018 at 03:59:29PM -0700, Nicolin Chen wrote:
> Texas Instruments INA3221 is a triple-channel shunt and bus
> voltage monitor. This patch adds a DT binding doc for it.
>
> Signed-off-by: Nicolin Chen <nicoleotsuka@xxxxxxxxx>
> ---
> Changelog
> v4->v5:
> * Replaced "input-id" with "reg" and added address-cells and size-cells
> * Replaced "input-label" with "label"
> * Replaced "shunt-resistor" with "shunt-resistor-micro-ohms"
> v3->v4:
> * Removed the attempt of putting labels in the node names
> * Added a new optional label property in the child node
> * Updated examples accordingly
> v2->v3:
> * Added a simple subject in the line 1
> * Fixed the shunt resistor value in the example
> v1->v2:
> * Dropped channel name properties
> * Added child node definitions.
> * * Added shunt resistor property in the child node
> * * Added status property to indicate connection status
> * * Changed to use child node name as the label of input source
>
> .../devicetree/bindings/hwmon/ina3221.txt | 49 +++++++++++++++++++
> 1 file changed, 49 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/hwmon/ina3221.txt
>
> diff --git a/Documentation/devicetree/bindings/hwmon/ina3221.txt b/Documentation/devicetree/bindings/hwmon/ina3221.txt
> new file mode 100644
> index 000000000000..e17a897f4803
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/ina3221.txt
> @@ -0,0 +1,49 @@
> +Texas Instruments INA3221 Device Tree Bindings
> +
> +1) ina3221 node
> + Required properties:
> + - compatible: Must be "ti,ina3221"
> + - reg: I2C address
> +
> + Optional properties:
> + = The node contains optional child nodes for three channels =
> + = Each child node describes the information of input source =
> +
> + - #address-cells: Required only if a child node is present. Must be 1.
> + - #size-cells: Required only if a child node is present. Must be 0.
> +
> + Example:
> +
> + ina3221@40 {
> + compatible = "ti,ina3221";
> + reg = <0x40>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + [ child node definitions... ]
> + };
> +
> +2) child nodes
> + Required properties:
> + - reg: Must be 0, 1 or 2, corresponding to IN1, IN2 or IN3 port of INA3221
> +
> + Optional properties:
> + - label: Name of the input source
> + - shunt-resistor-micro-ohms: Shunt resistor value in micro-Ohm
> + - status: Should be "disabled" if no input source
Don't need to explicitly list status.
> +
> + Example:
> +
> + input@0 {
> + reg = <0x0>;
> + status = "disabled";
> + };
> + input@1 {
> + reg = <0x1>;
> + shunt-resistor-micro-ohms = <5000>;
> + };
> + input@2 {
> + reg = <0x2>;
> + label = "VDD_5V";
> + shunt-resistor-micro-ohms = <5000>;
> + };
Please combine the examples into one complete example.
Rob
