Hi Mark, Thank you very much. > -----Original Message----- > From: Mark Brown [mailto:broonie@xxxxxxxxxx] > Sent: Tuesday, December 17, 2013 9:07 PM > To: Yang, Wenyou > Cc: lgirdwood@xxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; > grant.likely@xxxxxxxxxx; rob.herring@xxxxxxxxxxx; linux- > doc@xxxxxxxxxxxxxxx; vpalatin@xxxxxxxxxxxx; Ferre, Nicolas; > plagnioj@xxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; > devicetree@xxxxxxxxxxxxxxx > Subject: Re: [PATCH 1/3 v2] regulator: act8865: add PMIC act8865 driver > > On Tue, Dec 17, 2013 at 01:36:35PM +0800, Wenyou Yang wrote: > > Signed-off-by: Wenyou Yang <wenyou.yang@xxxxxxxxx> > > Much better. Still a few small issues though. > > > +/* ACt8865 voltage table */ > > +static const u32 act8865_voltages_table[] = { > > This is the wrong type for a voltage table but it looks like it > shouldn't be a voltage table at all - this looks like it should be > mapped as linear ranges. Change it, using unsigned int. It is not linear, can't be mapped as linear range. so using voltage table. > > > +static struct regulator_ops act8865_ops = { > > + .list_voltage = regulator_list_voltage_table, > > + .get_voltage_sel = regulator_get_voltage_sel_regmap, > > + .set_voltage_sel = regulator_set_voltage_sel_regmap, > > + .enable = regulator_enable_regmap, > > + .disable = regulator_disable_regmap, > > + .is_enabled = regulator_is_enabled_regmap, > > + .set_suspend_voltage = act8865_set_suspend_voltage, > > + .set_suspend_enable = regulator_enable_regmap, > > + .set_suspend_disable = regulator_disable_regmap, > > +}; > > This is missing a git di() operation. Add it, .map_voltage = regulator_map_voltage_ascend, > > > +#ifdef CONFIG_OF > > +static const struct of_device_id act8865_dt_ids[] = { > > + { .compatible = "active-semi,act8865" }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(of, act8865_dt_ids); > > active-semi needs adding to vendor-prefixes.txt. > Add it, active-semi Active-Semi International Inc > > + np = of_find_node_by_name(dev->of_node, "regulators"); > > + if (!np) { > > + dev_err(dev, "missing 'regulators' subnode in DT\n"); > > + return -EINVAL; > > + } > > + > > + for (i = 0; i < ARRAY_SIZE(rmatch); i++) > > + rmatch[i].name = act8865_reg[i].name; > > + > > + matched = of_regulator_match(dev, np, rmatch, ARRAY_SIZE(rmatch)); > > + if (matched <= 0) > > + return matched; > > You should register all regulators the device has regardless of how many > have parameters configured in the DT so that the settings can be read > back for diagnostic purposes. Change it. > > > + if (dev->of_node && !pdata) { > > + const struct of_device_id *id; > > + struct act8865_platform_data pdata_of; > > + > > + id = of_match_device(of_match_ptr(act8865_dt_ids), dev); > > + if (!id) > > + return -ENODEV; > > + > > + ret = act8865_pdata_from_dt(dev, of_node, &pdata_of); > > + if (ret < 0) > > + return ret; > > + > > + pdata = &pdata_of; > > + } else { > > + memset(of_node, 0, sizeof(of_node)); > > + } > > What's this memset() for? No meaningful, removed. > > > + rdev[i] = devm_regulator_register(&client->dev, > > + &act8865_reg[i], &config); > > > +err_unregister: > > + while (--i >= 0) > > + regulator_unregister(rdev[i]); > > The whole purpose of devm_ APIs is to avoid the need to explicitly > unregister, you shouldn't need to call regulator_unregister() at all. Remove regulator_unregister(rdev[i]) statement. Best Regard, Wenyou Yang -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
