This series aims to add iio backend support for AD7606X ADCs. In a nutshell, iio backend is a paradigm to shift the logic establishing the connexion between iio buffers and backend buffers into the backend's driver. This provides a more stable programming interface to the driver developers, and give more flexibility in the way the hardware communicates. The support will be first added on AD7606B, and on next patches AD7606C16 and AD7606C18 will be added. The series have been tested on a Zedboard, using the latest HDL available, i.e https://github.com/analogdevicesinc/hdl/commit/7d0a4cee1b5fa403f175af513d7eb804c3bd75d0 and an AD7606B FMCZ EKV. This HDL handles both the conversion trigger (through a PWM), and the end of conversion interruption, and is compatible with axi-adc, which is "iio-backendable". More information about this HDL design can be found at: https://wiki.analog.com/resources/eval/user-guides/ad7606x-fmc/hdl The support is thus separated in two parts: - PWM support was first added. My first intention was to make it available for any version of the driver, but the time required to handle the interruption is not neglectable, and I saw drifts that would eventually cause an overlapping SPI read with a new conversion trigger, whith catastrphic consequences. To mitigate this, CRC check must be implemented, but indeed increasing the samplerate causes more sample to be lost. Therefore, I decided to only allow PWM for iio-backend powered device as a first intention, leaving open the possibility to add the general compatibility afterwards. - IIO backend support was added: Once the PWM support was ready, the driver can be extended to iio-backend. The iio-backend powered version of the driver is a platform driver, and an exemple devicetree node is available in the bindings. The following features will be added in subsequent patch series: - software mode for iio backend - 18 bits mode (AD7606C18) - single read (IIO_CHAN_READ_RAW) Signed-off-by: Guillaume Stols <gstols@xxxxxxxxxxxx> --- Changes in v5: - Removal of an useless instruction move. - Removal of extra checks on the PWM setters functions. - Renaming of buffer postenable/predisable functions. - Usage of device_property_present to check if there is a backend property instead of trying to load the backend. - Improvement of error handling on PWM GPIO emulation, displaying an error in the kernel log in case the duty cycle set fails. - Link to v4: https://lore.kernel.org/r/20241009-ad7606_add_iio_backend_support-v4-0-6971a8c0f1d5@xxxxxxxxxxxx Changes in v4: - Removal of accepted patches. - Correction on fsleep (missing semicolon and incorrect spelling !). - Correction on buffer initialization that should not be conditionned by the presence or not of a PWM, but by the presence of a backend. - Addition of blank lines between blocks. - Modification of some declaration to switch variables to static. - Link to v3: https://lore.kernel.org/r/20241004-ad7606_add_iio_backend_support-v3-0-38757012ce82@xxxxxxxxxxxx Changes in v3: - Rebase on top of the series adding ad7606C16 and AD7606C18 support. - Addition of pwm-names actual values and improvement in the description. - Introduction of .num_adc_channels field in ad7606_chip_info that defines the number of hardware inputs. - Introduction of ad7606_bus_info which couples hardware and wiring informations. - Addition of a delay in the scan_direct function for the backend. - Link to v2: https://lore.kernel.org/r/20240920-ad7606_add_iio_backend_support-v2-0-0e78782ae7d0@xxxxxxxxxxxx Changes in v2: - Logical change in dt-bindings, using a flag for the interface instead of infering it from the value of the "reg" property. - Removal of get_platform_match_data addition, instead the logic is directly used in the file. - Removal of use and export of pwm_get_state_hw, returning the configured frequency instead of the running one. - Correction on various typos, whitespaces, bad order of includes. - Separation of SPI conditions and PWM disabling for no backend in other commits. - Link to v1: https://lore.kernel.org/r/20240815-ad7606_add_iio_backend_support-v1-0-cea3e11b1aa4@xxxxxxxxxxxx --- Guillaume Stols (8): dt-bindings: iio: adc: ad7606: Remove spi-cpha from required dt-bindings: iio: adc: ad7606: Add iio backend bindings Documentation: iio: Document ad7606 driver iio: adc: ad7606: Add PWM support for conversion trigger iio: adc: ad7606: Add compatibility to fw_nodes iio: adc: ad7606: Introduce num_adc_channels iio: adc: ad7606: Add iio-backend support iio: adc: ad7606: Disable PWM usage for non backend version .../devicetree/bindings/iio/adc/adi,ad7606.yaml | 72 ++- Documentation/iio/ad7606.rst | 145 ++++++ Documentation/iio/index.rst | 1 + MAINTAINERS | 1 + drivers/iio/adc/Kconfig | 2 + drivers/iio/adc/ad7606.c | 576 +++++++++++++++------ drivers/iio/adc/ad7606.h | 51 +- drivers/iio/adc/ad7606_par.c | 122 ++++- drivers/iio/adc/ad7606_spi.c | 96 ++-- 9 files changed, 838 insertions(+), 228 deletions(-) --- base-commit: 465644ac29536d10178b5ca4684d0b84765b9fa4 change-id: 20240725-ad7606_add_iio_backend_support-c401305a6924 Best regards, -- Guillaume Stols <gstols@xxxxxxxxxxxx>
