Re: [PATCH net-next v2 8/9] microchip: lan865x: add driver support for Microchip's LAN865X MACPHY

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 23/10/2023 17:46, Parthiban Veerasooran wrote:
> The LAN8650/1 is designed to conform to the OPEN Alliance 10BASE‑T1x
> MAC‑PHY Serial Interface specification, Version 1.1. The IEEE Clause 4
> MAC integration provides the low pin count standard SPI interface to any
> microcontroller therefore providing Ethernet functionality without
> requiring MAC integration within the microcontroller. The LAN8650/1
> operates as an SPI client supporting SCLK clock rates up to a maximum of
> 25 MHz. This SPI interface supports the transfer of both data (Ethernet
> frames) and control (register access).
> 
> By default, the chunk data payload is 64 bytes in size. A smaller payload
> data size of 32 bytes is also supported and may be configured in the
> Chunk Payload Size (CPS) field of the Configuration 0 (OA_CONFIG0)
> register. Changing the chunk payload size requires the LAN8650/1 be reset
> and shall not be done during normal operation.
> 
> The Ethernet Media Access Controller (MAC) module implements a 10 Mbps
> half duplex Ethernet MAC, compatible with the IEEE 802.3 standard.
> 10BASE-T1S physical layer transceiver integrated into the LAN8650/1. The
> PHY and MAC are connected via an internal Media Independent Interface
> (MII).
> 
> Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@xxxxxxxxxxxxx>
> ---
>  MAINTAINERS                              |   6 +
>  drivers/net/ethernet/microchip/Kconfig   |  11 +
>  drivers/net/ethernet/microchip/Makefile  |   2 +
>  drivers/net/ethernet/microchip/lan865x.c | 415 +++++++++++++++++++++++
>  4 files changed, 434 insertions(+)
>  create mode 100644 drivers/net/ethernet/microchip/lan865x.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 9580be91f5e9..1b1bd3218a2d 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -14001,6 +14001,12 @@ L:	netdev@xxxxxxxxxxxxxxx
>  S:	Maintained
>  F:	drivers/net/ethernet/microchip/lan743x_*
>  
> +MICROCHIP LAN8650/1 10BASE-T1S MACPHY ETHERNET DRIVER
> +M:	Parthiban Veerasooran <parthiban.veerasooran@xxxxxxxxxxxxx>
> +L:	netdev@xxxxxxxxxxxxxxx
> +S:	Maintained
> +F:	drivers/net/ethernet/microchip/lan865x.c
> +
>  MICROCHIP LAN87xx/LAN937x T1 PHY DRIVER
>  M:	Arun Ramadoss <arun.ramadoss@xxxxxxxxxxxxx>
>  R:	UNGLinuxDriver@xxxxxxxxxxxxx
> diff --git a/drivers/net/ethernet/microchip/Kconfig b/drivers/net/ethernet/microchip/Kconfig
> index 329e374b9539..596caf59dea6 100644
> --- a/drivers/net/ethernet/microchip/Kconfig
> +++ b/drivers/net/ethernet/microchip/Kconfig
> @@ -59,4 +59,15 @@ source "drivers/net/ethernet/microchip/lan966x/Kconfig"
>  source "drivers/net/ethernet/microchip/sparx5/Kconfig"
>  source "drivers/net/ethernet/microchip/vcap/Kconfig"
>  
> +config LAN865X
> +	tristate "LAN865x support"
> +	depends on SPI
> +	depends on OA_TC6
> +	help
> +      	  Support for the Microchip LAN8650/1 Rev.B0 MACPHY Ethernet chip. It
> +	  uses OPEN Alliance 10BASE-T1x Serial Interface specification.
> +
> +      	  To compile this driver as a module, choose M here. The module will be
> +          called lan865x.

That's odd indentation. Kconfig help goes with tab and two spaces.

> +
>  endif # NET_VENDOR_MICROCHIP
> diff --git a/drivers/net/ethernet/microchip/Makefile b/drivers/net/ethernet/microchip/Makefile
> index bbd349264e6f..1fa4e15a067d 100644
> --- a/drivers/net/ethernet/microchip/Makefile
> +++ b/drivers/net/ethernet/microchip/Makefile
> @@ -12,3 +12,5 @@ lan743x-objs := lan743x_main.o lan743x_ethtool.o lan743x_ptp.o
>  obj-$(CONFIG_LAN966X_SWITCH) += lan966x/
>  obj-$(CONFIG_SPARX5_SWITCH) += sparx5/
>  obj-$(CONFIG_VCAP) += vcap/

...

> +static void lan865x_remove(struct spi_device *spi)
> +{
> +	struct lan865x_priv *priv = spi_get_drvdata(spi);
> +
> +	oa_tc6_exit(priv->tc6);
> +	unregister_netdev(priv->netdev);
> +	free_netdev(priv->netdev);
> +}
> +
> +#ifdef CONFIG_OF

Drop ifdef

> +static const struct of_device_id lan865x_dt_ids[] = {
> +	{ .compatible = "microchip,lan865x" },
> +	{ /* Sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, lan865x_dt_ids);
> +#endif
> +
> +#ifdef CONFIG_ACPI
> +static const struct acpi_device_id lan865x_acpi_ids[] = {
> +	{ .id = "LAN865X",
> +	},
> +	{},
> +};
> +MODULE_DEVICE_TABLE(acpi, lan865x_acpi_ids);
> +#endif
> +
> +static struct spi_driver lan865x_driver = {
> +	.driver = {
> +		.name = DRV_NAME,
> +#ifdef CONFIG_OF

Drop ifdef

> +		.of_match_table = lan865x_dt_ids,
> +#endif
> +#ifdef CONFIG_ACPI

Why do you need this ifdef?

> +		   .acpi_match_table = ACPI_PTR(lan865x_acpi_ids),
> +#endif
> +	 },
> +	.probe = lan865x_probe,
> +	.remove = lan865x_remove,
> +};
> +module_spi_driver(lan865x_driver);
> +
> +MODULE_DESCRIPTION(DRV_NAME " 10Base-T1S MACPHY Ethernet Driver");
> +MODULE_AUTHOR("Parthiban Veerasooran <parthiban.veerasooran@xxxxxxxxxxxxx>");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("spi:" DRV_NAME);

You should not need MODULE_ALIAS() in normal cases. If you need it,
usually it means your device ID table is wrong.


Best regards,
Krzysztof





[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux