From: Lars Poeschel <poeschel@xxxxxxxxxxx>
The device tree property should be more descriptive.
microchip seems more reasonable than mcp. As there are no
in tree users of this property, so the rename can still be
done without pain.
Signed-off-by: Lars Poeschel <poeschel@xxxxxxxxxxx>
---
.../devicetree/bindings/gpio/gpio-mcp23s08.txt | 16 ++++++++--------
drivers/gpio/gpio-mcp23s08.c | 14 +++++++++-----
2 files changed, 17 insertions(+), 13 deletions(-)
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
index 629d0ef..f207b7c 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
@@ -3,10 +3,10 @@ Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for
Required properties:
- compatible : Should be
- - "mcp,mcp23s08" for 8 GPIO SPI version
- - "mcp,mcp23s17" for 16 GPIO SPI version
- - "mcp,mcp23008" for 8 GPIO I2C version or
- - "mcp,mcp23017" for 16 GPIO I2C version of the chip
+ - "microchip,mcp23s08" for 8 GPIO SPI version
+ - "microchip,mcp23s17" for 16 GPIO SPI version
+ - "microchip,mcp23008" for 8 GPIO I2C version or
+ - "microchip,mcp23017" for 16 GPIO I2C version of the chip
- #gpio-cells : Should be two.
- first cell is the pin number
- second cell is used to specify flags. Flags are currently unused.
@@ -15,10 +15,10 @@ Required properties:
SPI uses this to specify the chipselect line which the chip is
connected to. The driver and the SPI variant of the chip support
multiple chips on the same chipselect. Have a look at
- mcp,spi-present-mask below.
+ microchip,spi-present-mask below.
Required device specific properties (only for SPI chips):
-- mcp,spi-present-mask : This is a present flag, that makes only sense for SPI
+- microchip,spi-present-mask : This is a present flag, that makes only sense for SPI
chips - as the name suggests. Multiple SPI chips can share the same
SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a
chip connected with the corresponding spi address set. For example if
@@ -30,7 +30,7 @@ Required device specific properties (only for SPI chips):
Example I2C:
gpiom1: gpio@20 {
- compatible = "mcp,mcp23017";
+ compatible = "microchip,mcp23017";
gpio-controller;
#gpio-cells = <2>;
reg = <0x20>;
@@ -38,7 +38,7 @@ gpiom1: gpio@20 {
Example SPI:
gpiom1: gpio@0 {
- compatible = "mcp,mcp23s17";
+ compatible = "microchip,mcp23s17";
gpio-controller;
#gpio-cells = <2>;
spi-present-mask = <0x01>;
diff --git a/drivers/gpio/gpio-mcp23s08.c b/drivers/gpio/gpio-mcp23s08.c
index 6a4470b..73cf236 100644
--- a/drivers/gpio/gpio-mcp23s08.c
+++ b/drivers/gpio/gpio-mcp23s08.c
@@ -483,10 +483,12 @@ fail:
#ifdef CONFIG_SPI_MASTER
static struct of_device_id mcp23s08_spi_of_match[] = {
{
- .compatible = "mcp,mcp23s08", .data = (void *) MCP_TYPE_S08,
+ .compatible = "microchip,mcp23s08",
+ .data = (void *) MCP_TYPE_S08,
},
{
- .compatible = "mcp,mcp23s17", .data = (void *) MCP_TYPE_S17,
+ .compatible = "microchip,mcp23s17",
+ .data = (void *) MCP_TYPE_S17,
},
{ },
};
@@ -496,10 +498,12 @@ MODULE_DEVICE_TABLE(of, mcp23s08_spi_of_match);
#if IS_ENABLED(CONFIG_I2C)
static struct of_device_id mcp23s08_i2c_of_match[] = {
{
- .compatible = "mcp,mcp23008", .data = (void *) MCP_TYPE_008,
+ .compatible = "microchip,mcp23008",
+ .data = (void *) MCP_TYPE_008,
},
{
- .compatible = "mcp,mcp23017", .data = (void *) MCP_TYPE_017,
+ .compatible = "microchip,mcp23017",
+ .data = (void *) MCP_TYPE_017,
},
{ },
};
@@ -621,7 +625,7 @@ static int mcp23s08_probe(struct spi_device *spi)
if (match) {
type = (int)match->data;
status = of_property_read_u32(spi->dev.of_node,
- "mcp,spi-present-mask", &spi_present_mask);
+ "microchip,spi-present-mask", &spi_present_mask);
if (status) {
dev_err(&spi->dev, "DT has no spi-present-mask\n");
return -ENODEV;
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
