[PATCH v3] mfd: DT bindings for the palmas family MFD

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the various binding files for the palmas family of chips. There is a
top level MFD binding then a seperate binding for regulators IP blocks on chips.

Signed-off-by: Graeme Gregory <gg@xxxxxxxxxxxxxxx>
Signed-off-by: J Keerthy <j-keerthy@xxxxxx>
Signed-off-by: Ian Lartey <ian@xxxxxxxxxxxxxxx>
Reviewed-by: Stephen Warren <swarren@xxxxxxxxxx> 
---
 Documentation/devicetree/bindings/mfd/palmas.txt   |   49 +++++++++++++
 .../devicetree/bindings/regulator/palmas-pmic.txt  |   72 ++++++++++++++++++++
 2 files changed, 121 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/palmas.txt
 create mode 100644 Documentation/devicetree/bindings/regulator/palmas-pmic.txt

diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt
new file mode 100644
index 0000000..7bcd59c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/palmas.txt
@@ -0,0 +1,49 @@
+* palmas device tree bindings
+
+The TI palmas family current members :-
+twl6035 (palmas)
+twl6037 (palmas)
+tps65913 (palmas)
+tps65914 (palmas)
+
+Required properties:
+- compatible : Should be from the list
+  ti,twl6035
+  ti,twl6036
+  ti,twl6037
+  ti,tps65913
+  ti,tps65914
+  ti,tps80036
+and also the generic series names
+  ti,palmas
+- interrupt-controller : palmas has its own internal IRQs
+- #interrupt-cells : should be set to 2 for IRQ number and flags
+  The first cell is the IRQ number.
+  The second cell is the flags, encoded as the trigger masks from
+  Documentation/devicetree/bindings/interrupts.txt
+- interrupt-parent : The parent interrupt controller.
+
+Optional properties:
+  ti,mux-padX : set the pad register X (1-2) to the correct muxing for the
+  		hardware, if not set will use muxing in OTP.
+
+Example:
+
+palmas {
+	compatible = "ti,twl6035", "ti,palmas";
+	reg = <0x48>
+	interrupt-parent = <&intc>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	ti,mux-pad1 = <0>;
+	ti,mux-pad2 = <0>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pmic {
+		compatible = "ti,twl6035-pmic", "ti,palmas-pmic";
+		....
+	};
+}
diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt
new file mode 100644
index 0000000..d5a3086
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt
@@ -0,0 +1,72 @@
+* palmas regulator IP block devicetree bindings
+
+Required properties:
+- compatible : Should be from the list
+  ti,twl6035-pmic
+  ti,twl6036-pmic
+  ti,twl6037-pmic
+  ti,tps65913-pmic
+  ti,tps65914-pmic
+and also the generic series names
+  ti,palmas-pmic
+- interrupt-parent : The parent interrupt controller which is palmas.
+- interrupts : The interrupt number and the type which can be looked up here:
+	       arch/arm/boot/dts/include/dt-bindings/interrupt-controller/irq.h
+- interrupts-name: The names of the individual interrupts.
+
+Optional properties:
+- ti,ldo6-vibrator : ldo6 is in vibrator mode
+
+Optional nodes:
+- regulators : Must contain a sub-node per regulator from the list below.
+	       Each sub-node should contain the constraints and initialization
+	       information for that regulator. See regulator.txt for a
+	       description of standard properties for these sub-nodes.
+	       Additional custom properties  are listed below.
+
+	       For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP,
+	       smps45, smps457, smps7 depending on variant, smps6, smps[8-10],
+	       ldo[1-9], ldoln, ldousb.
+
+	       Optional sub-node properties:
+	       ti,warm-reset - maintain voltage during warm reset(boolean)
+	       ti,roof-floor - control voltage selection by pin(boolean)
+	       ti,sleep-mode - mode to adopt in pmic sleep 0 - off, 1 - auto,
+	       2 - eco, 3 - forced pwm
+	       ti,tstep - slope control 0 - Jump, 1 10mV/us, 2 5mV/us, 3 2.5mV/us
+	       ti,smps-range - OTP has the wrong range set for the hardware so override
+	       0 - low range, 1 - high range.
+
+Example:
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+pmic {
+	compatible = "ti,twl6035-pmic", "ti,palmas-pmic";
+	interrupt-parent = <&palmas>;
+	interrupts = <14 IRQ_TYPE_NONE>;
+	interrupts-name = "short-irq";
+
+	ti,ldo6-vibrator;
+
+	regulators {
+		smps12_reg : smps12 {
+			regulator-name = "smps12";
+			regulator-min-microvolt = < 600000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-always-on;
+			regulator-boot-on;
+			ti,warm-reset;
+			ti,roof-floor;
+			ti,mode-sleep = <0>;
+			ti,tstep = <0>;
+			ti,smps-range = <1>;
+		};
+
+		ldo1_reg: ldo1 {
+			regulator-name = "ldo1";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+	};
+};
-- 
1.7.5.4
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux