On 3/12/2013 1:40 PM, Manjunathappa, Prakash wrote: > From: Murali Karicheri <m-karicheri2@xxxxxx> > > Get back missed out binding documentation submitted along > with below patch: > "spi/davinci: add OF support for the spi controller" This is not really the correct description of this patch. Years later its mostly irrelevant that binding documentation did not get applied along with the actual usage. > > [prakash.pm@xxxxxx: Follow DT naming convention for compatible property] > Signed-off-by: Murali Karicheri <m-karicheri2@xxxxxx> > Reviewed-by: Grant Likely <grant.likely@xxxxxxxxxxxx> > Signed-off-by: Manjunathappa, Prakash <prakash.pm@xxxxxx> > --- > .../devicetree/bindings/spi/spi-davinci.txt | 51 ++++++++++++++++++++ > 1 files changed, 51 insertions(+), 0 deletions(-) > create mode 100644 Documentation/devicetree/bindings/spi/spi-davinci.txt > > diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt > new file mode 100644 > index 0000000..75ad9ac > --- /dev/null > +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt > @@ -0,0 +1,51 @@ > +Davinci SPI controller device bindings > + > +Required properties: > +- #address-cells: number of cells required to define a chip select > + address on the SPI bus. Should be set to 1. > +- #size-cells: should be zero. > +- compatible: > + - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family > + - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family > +- reg: Offset and length of SPI controller register space > +- num-cs: Number of chip selects > +- ti,davinci-spi-intr-line: interrupt line used to connect the SPI > + IP to the interrupt controller withn the SoC. Possible values > + are 0 and 1. Manual says one of the two possible interrupt > + lines can be tied to the interrupt controller. Set this > + based on a specifc SoC configuration. > +- interrupts: interrupt number mapped to CPU. > +- clocks: spi clk phandle > + > +Example of a NOR flash slave device (n25q032) connected to DaVinci > +SPI controller device over the SPI bus. > + > +spi0:spi@20BF0000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "ti,dm6446-spi"; > + reg = <0x20BF0000 0x1000>; > + num-cs = <4>; > + ti,davinci-spi-intr-line = <0>; > + interrupts = <338>; > + clocks = <&clkspi>; > + > + flash: n25q032@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "st,m25p32"; > + spi-max-frequency = <25000000>; > + reg = <0>; > + > + partition@0 { > + label = "u-boot-spl"; > + reg = <0x0 0x80000>; > + read-only; > + }; > + > + partition@1 { > + label = "test"; > + reg = <0x80000 0x380000>; > + }; > + }; Looks like the tabs were messed up when you took Murali's patch. Thanks, Sekhar -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html